Filter
Top Products
To Set the Decimal Point
1. If it's not already shown,
press MENU until the unit
displays DEC.P
2. Press ᮣ/DEV to show the
current decimal point location.
3. Press ᮡ/MAX to move the
decimal point to the desired
location. The choices are
FFFF or FFF.F.
4. Press MENU to store the value.
5. Press RESET twice to display the current temperature.
To Select Temperature Unit
(Fahrenheit or Celsius):
1. Press MENU until the display
shows RD.CF
2. Press ᮣ/DEV to display the
current temperature unit.
3. Press ᮡ/MAX to select
between °F and °C.
4. Press MENU to store the value.
5. Press RESET twice to display the current temperature.
To Enter Setpoints:
1. Press SETPTS to display the
current setpoint. The leftmost
digit will flash.
2. Press ᮣ/DEV to select the
digit you want to change.
3. Press ᮡ/MAX to increase the
value of the flashing digit.
4. Press SETPTS to store the
setpoint.
5. Repeat steps 1 through 4 to enter the next setpoint.
DP25-TC and DP25B-TC
PROGRAMMABLE DIGITAL
THERMOCOUPLE CONTROLLER
USA
MADE IN
This device is marked with the international caution symbol. It is important
to read the Setup Guide before installing or commissioning this device as
it contains important information relating to safety and EMC.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to
the European New Approach Directives. OMEGA will add the CE mark to every
appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right
to alter specifications without notice.
TRADEMARK NOTICE:
®
omega.com
®
, and ,
are trademarks of OMEGA Engineering, Inc.
®
WARNING: These products are not designed for use in, and should not be used
for, patient connected applications.
MQS3732/1205
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in
materials and workmanship for a period of one (1) year from the date of
purchase. In addition to OMEGA’s standard warranty period, OMEGA
Engineering will extend the warranty period for four (4) additional years if the
warranty card enclosed with each instrument is returned to OMEGA.
If the unit malfunctions, it must be returned to the factory for evaluation.
OMEGA’s Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by
OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or unauthorized
modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of having been damaged as a result of
excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
OMEGA’s control. Components which wear are not warranted, including but not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products.
However, OMEGA neither assumes responsibility for any omissions or
errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either
verbal or written. OMEGA warrants only that the parts manufactured by it
will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER,
EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED
WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are
exclusive, and the total liability of OMEGA with respect to this order,
whether based on contract, warranty, negligence, indemnification, strict
liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEGA be
liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall
it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with
any nuclear installation or activity; or (2) in medical applications or used on
humans. Should any Product(s) be used in or with any nuclear installation or
activity, medical application, used on humans, or misused in any way, OMEGA
assumes no responsibility as set forth in our basic WARRANTY/DISCLAIMER
language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA
harmless from any liability or damage whatsoever arising out of the use of the
Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER
FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on
the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please
have the following information available
BEFORE contacting OMEGA:
1. P.O. number under which the
product was PURCHASED,
2. Model and serial number of the
product under warranty, and
3. Repair instructions and/or specific
problems relative to the product.
FOR NON-W
ARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following information
available BEFORE contacting OMEGA:
1. P.O. number to cover the COST of
the repair,
2. Model and serial number of product,
and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2005 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or reduced
to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of OMEGA ENGINEERING, INC.
PATENT NOTICE: This product is covered by one or more of the following
patents: U.S. Pat. No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599;
2052600 / ITALY 1249456; 1250938 / FRANCE BREVET No. 91 12756 / SPAIN
2039150; 2048066 / UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY
DE 41 34398 C2. The “Meter Case Bezel Design” is a trademark of NEWPORT
Electronics, Inc. USED UNDER LICENSE. Other U.S. and International patents
pending or applied for.
56
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡᮣ
SETPTS /DEV MENU RESET
/MAX
ᮡ
ᮣ
SETPTS /DEV MENU RESET
/MAX
Servicing North America:
USA: One Omega Drive, P.O. Box 4047
ISO 9001 Certified Stamford CT 06907-0047
TEL: (203) 359-1660 FAX: (203) 359-7700
e-mail: info@omega.com
Canada: 976 Bergar
Laval (Quebec) H7L 5A1
TEL: (514) 856-6928 FAX: (514) 856-6886
e-mail: info@omega.ca
For immediate technical or application assistance:
USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
®
Customer Service: 1-800-622-2378 / 1-800-622-BEST
®
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN
®
Mexico and TEL: (001)800-TC-OMEGA
®
FAX: (001) 203-359-7807
Latin American: En Espa
ñol: (001) 203-359-7803
e-mail: espanol@omega.com
Servicing Europe:
Czech Republic: Frystatska 184, 733 01 Karviná
TEL: +420 59 6311899 FAX: +420 59 6311114
e-mail: info@omegashop.cz
Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 7056 9398-0 FAX: +49 7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: info@omega.de
United Kingdom: One Omega Drive
ISO 9002 Certified River Bend Technology Centre
Northbank, Irlam Manchester M44 5BD United Kingdom
TEL: +44 161 777 6611 FAX: +44 161 777 6622
Toll Free in England: 0800 488 488
e-mail: sales@omega.co.uk
OMEGAnet
®
On-Line Service
www.omega.com
Internet e-mail
info@omega.com
®
®