Filter
Top Products
14
ACCESSORIES —
Condensing Unit
Low Ambient Kit 913549A- Maintains system
pressures during low ambient conditions.
PHYSICAL AND ELECTRICAL SPECIFICATIONS / OUTDOOR UNITS
10.1 EER —High Effi ciency — Three Phase
COPPER WIRE SIZE — AWG
(1% Voltage Drop)
Supply Wire Length-Feet
Supply Circuit
200 150 100 50
Ampacity
6 8 10 14 15
46812 20
46810 25
44610 30
3468 35
3468 40
2346 45
2346 50
2346 55
1234 60
Model No. T3BN- 090C 090W 120C 120W
Electrical Data
Volts-Phase-Hz
280/230-3-60 460-3-60 280/230-3-60 460-3-60
380/420-3-50 380/420-3-50
Voltage Range (Min-Max) 187-253 414-506 187-253 414-506
Total Amps 32.1 16.4 33.4 17.2
Min Circuit Ampacity 41.4 21.7 43 22.7
Delay Fuse Max. (1) 60 35 70 35
Wire Size/Max Length (AWG 60°C Cu) 4/100 8/100 4/100 8/100
Wire Size/Max Length (AWG 75°C Cu) 6/100 8/100 4/100 8/100
Component Data
Coil
Area (ft^2) 31.94 31.94 31.94 31.94
Rows-FPI 2-16 2-16 2-18 2-18
Tube Dia. 3/8” OD 3/8” OD 3/8” OD 3/8” OD
Fan Motor
Volts-Phase-Hz
280/230-3-60 460-3-60 280/230-3-60 460-3-60
380/420-3-50 380/420-3-50
Qty 1111
Horsepower 3/4 3/4 3/4 3/4
Full Load Amps 3.3 1.7 3.3 1.7
Fan Blade
Dia./Pitch/#Blades 30/19/3 30/19/3 30/26/3 30/26/3
RPM/CFM (Max-Total) 825/7500 825/7500 825/8500 825/8500
Compressor
Data
Volts-Phase-Hz 280/230-3-60 460-3-60 280/230-3-60 460-3-60
Qty./Type 1 / Scroll 1 / Scroll 1 / Scroll 1 / Scroll
RLA 28.8 14.7 30.1 15.5
LRA 195 95 225 114
Stages/Percent 1 / 100 1 / 100 1 / 100 1 / 100
Crankcase Heater Qty./Type 1 / Band 1 / Band 1 / Band 1 / Band
Refrigerant Suction Line-Length/O.D. 0 - 15 ft. 1 1/8” 1 1/8” 1 1/8” 1 1/8”
(Liq. Line All Lengths - 5/8” O.D.)
Circuits (Qty) - 1
16 - 25 ft 1 3/8” (3) 1 3/8” (3) 1 3/8” (3) 1 3/8” (3)
26 - 75 ft. 1 3/8” (3) 1 3/8” (3) 1 3/8” (3) 1 3/8” (3)
Refrigerant Charge
Holding Charge 56 56 90 90
R-22 Ounces
Total System with 15’ Line Set (2) 374 374 486 486
Weight Net 413 413 423 423
Approximate (lbs.) Ship 425 425 435 435
(1) HACR Type Circuit Breakers may be used.
(2) Add 9.0 oz. of refrigerant per 5 feet of additional line set.
(3) Requires a 1-3/8” to 1-1/8” reducer line to unit.