Filter
Top Products
JIMMY SERIES HYDRAULIC REBAR BENDERS — OPERATION AND PARTS MANUAL — REV. #9 (01/04/08) — PAGE 9
trahCeziSrabeR.2elbaT
ledoM5315BJ5317BJ0905BJ0907BJ0908BJ0819BJ09011BJ
suidaRgnidneB
°531°531°09°09°09°081°081
)31#/M01(4#
★★★★
)61#/M51(5#
★★★★★★★★
)91#/M02(6#
★★★★★★★★★★★
)22#/AN(7#
★★★★★★★★★★★★★
)52#/M52(8#
★★★★★★★★★
)92#/M03(9#
★★★ ★★
)23#/AN(01#
★★
)63#/M53(11#
★★★
* Minimum bend measured from bottom of machine to top of angle.
** American Concrete Institute (ACI) has approved the wheel used in this device as the proper radius for bending the bar size indicated; Concrete Reinforcing Steel
Institute(CRSI) requirements are met for the bar size indicated.
snoitacificepSredneBrabeR.1elbaT
ledoM5315BJ5317BJ0905BJ0907BJ0908BJ0819BJ09011BJ
elgnAgnidneB
°531°531°09°09°09°081°09
yticapaCrabeR
)eziSraB(
5#,4#7#,6#6#,5#,4#8#,7#,6#9#,8#,7#,6#01#,9#,8#,7#11#,01#,9#,8#
dneBmuminiM
*)mc(.ni
)7.21(5)7.21(5)7.21(5)3.02(8)3.02(8)9.72(11)6.53(41
nosehcnignicapSraBmuminiM
retnec
22333 5.35.3
dneB;rebmuNraBdevorppA-ICA
**suidaR
°531;5#°531;7#°09;5#°09;7#°09;8#°081;9#°09;11#
)gk(.blthgieW
)01(22)21(62)21(62)62(85)92(26)54(001)05(011
)gk(.blthgieWgnippihS
)51(43)12(74)81(93)33(47)04(98)45(911)26(631
)mc(.nisnoisnemiDllarevO
5.3x11x32
)9.8x9.72x4.85(
3x9x91
)6.7x9.22x3.84(
5.4x9x71
)4.11x9.22x2.34(
5.5x5.21x5.12
)41x8.13x6.45(
5.5x41x72
)41x6.53x6.86(
6x71x91
)2.51x2.34x3.84(
6x91x72
)2.51x3.84x6.86(
)mc(.nisnoisnemiDgnippihS
42x31x03
)16x33x67(
42x31x03
)16x33x67(
42x31x03
)16x33x67(
51x31x42
)83x33x16(
51x31x42
)83x33x16(
51x31x42
)83x33x16(
51x31x42
)83x33x16(
snoitacilppA
dneBdradnatS°09
✓✓✓✓✓✓✓
kooHenaC°081
✓
sdneBtesffO
✓✓✓✓✓✓✓
gninethgiartS
✓✓✓✓✓✓✓
kooHeiTdnapurritScimsieS
✓✓
Rebar Size:
Standard 1/8 inch increments
(Metric Hard/Soft
Conversion)
Example:
#8 Rebar ÷ 8 = 1-inch
#4 Rebar ÷ 8 = 4/8 = 1/2-inch
NOTE
★★★
ACI/CRSI Approved for this size
★★
Acceptable bend radius for ACI/CRSI requirements
★
Capable of bending rebar but does not meet ACICRSI requirements
Not capable of bending this size rebar
JIMMY SERIES HYDRAULIC REBAR BENDERS — SPECIFICATIONS (REBAR UNIT)