Filter
Top Products
16
6
OUTLINES & DIMENSIONS
INDOOR UNIT
PEAD-A24, 30, 36, 42AA
3-ø2.9(1/8) mounting hole
Air filter
Refrigerant piping
flare connection (liquid)
Liquid pipe
Gas pipe
ø9.52
(3/8)
ø15.88
(5/8)
Fresh air intake ø100(3-15/16)
knock out hole
A
Model
1400
1100
PEAD-A24, 30AA
PEAD-A36, 42AA
GFBCDE
1000
14
136015001454
1154 1060
11
1200
1300 1358
1058
Suspension bolt hole
4-14x30(9/16X1-3/16) Slot
(O.D.ø32(1-1/4))
Drain pipe
Drain pipe(O.D.ø32(1-1/4))(Spontaneous draining)
Terminal block(Remote controller transmission line)
Terminal block(Indoor/Outdoor connection line)
Control box
Drain pump
Refrigerant piping
flare connection (gas)
1
1
2
2
Drain pipe(O.D. ø32(1-1/4))
(Emergency draining)
2xE-ø2.9(1/8)
Air
inlet
Air
outlet
2X2-ø2.9(1/8)
(4-15/16)
ø
125
120
120
57(2-1/4)
78(3-1/8)
200(7-7/8)
378(12-7/16)
Unit:mm(in.)
(43-5/16)
(55-1/8) (57-1/4)
(45-7/16) (47-1/4)
(59-1/16)
(53-9/16)
(41-3/4) (39-3/8)
(51-3/16) (53-1/2)
(41-11/16)
21(7/8)
(8-5/16)
(5-3/8)
135
153(6-1/16)
(2-11/16)
(5-3/8)
(Suspension bolt pitch)
21
G
18(3/4)
210
40
(1-5/8)
40(1-5/8)
250(9-7/8)
40(1-5/8)
33(1-5/16)
122
(4-13/16)
D(Duct)
20
(13/16)
100(3-15/16)X(E-1)=F30(1-3/16)
100(3-15/16)
217(8-9/16)
41(1-5/8)
100(3-15/16)
356(1/16)
67136
732(28-7/8)
700
(27-9/16)32(1-5/16)
238
(9-3/8)
10(7/16)
23(15/16)178(7-1/16)
643(25-3/8)
23(15/16)
C
B(Suspension bolt pitch)
A
10(7/16)
57
(2-1/4)
58
(2-5/16)
15(5/8)
Note 4
10
12
1280
330
4
49
54 320
5
990
MLKJN
1200
1500
H
N-ø2.9(1/8)
(4-7/16) (4-7/16)
(50-7/16)
(39)
(12-5/8)
(13)(1-15/16)
(2-3/16)(59-1/16)
(47-1/4)
-7/16
0
(2-9/16 )
(11-13/16)
(27-9/16)
(11-13/16)
(9-7/8~11-13/16)
Less than 700
Less than 300
(Actual length)
65
0
-10
JKX(L-1)=MJ6
(1/4)
112 112 11
(7/16)
K
50(2)
250~300
450(17-3/4)
50(2)
H
777(30-5/8)
450(17-3/4)
More than 300
More than 20(13/16)
More than 10(7/16)
<accessory>
Drain hose (I.D.ø32(1-1/4))
Access door
Note2
Make the access door at the appointed position properly for service maintenance.
Ceiling surface
Access door
Required space for service and maintenance
NOTE 1. Use M10 screw for the Suspension bolt (field supply).
2. Keep the service space for the maintenance at the bottom.
3. This chart indicates for PEAD-A24·30·36·42AA models,which have 2 fans.
4. In case of the inlet duct is used,remove the air filter (supply with the unit), then install the filter (field supply) at suction side.