Mitsubishi Electronics 36FL3 Air Conditioner User Manual


 
3
ON/OFF
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
A
1
2. Operation
Operating range
Indoor air intake temperature Outdoor air intake temperature
Cooling
Maximum 95 °F DB, 71 °F WB 115 °F DB
Minimum 67 °F DB, 57 °F WB 0 °F DB*
Heating
Maximum 80 °F DB, 67 °F WB 75 °F DB, 65 °F WB
Minimum 70 °F DB, 60 °F WB 17 °F DB, 15 °F WB
* With wind baffle installed. Without wind baffle, the minumum temperature will be
23 °F DB.
2.1. Switching the unit on/off
The power supply should not be turned off while the air conditioner is in use. This
can cause the unit to break down.
1 Press the ON/OFF button.
A The ON indicator should light up.
Even if you press the ON/OFF button immediately after shutting down the opera-
tion in progress, the air conditioner will not start for about three minutes. This is to
prevent the internal components from being damaged.
If the operation stops due to a power failure, the unit will not automatically restart
until the power has been restored. Press the ON/OFF button to restart.
2.2. Mode select
1 If the unit is off, press the ON/OFF button to turn it on.
A The ON indicator should light up.
2
Press the operation mode button
C
and select the operation mode.
B
COOL Cooling mode AUTO Automatic (cooling/heating) mode
(For PLH/PCH/PKH)
DRY Drying mode HEAT Heating mode
(For PLH/PCH/PKH)
FAN Fan mode
(For PL/PC/PK)
Note:
The heating display and the automatic display does not appear in models that
operate exclusively as cooling only air-conditioner.
2.3. Selecting a temperature
ss
ss
s To decrease the room temperature:
1 Press set temperature button to set the desired temperature.
A The selected temperature is displayed.
Each time you press the button, the temperature value decreases by 2 °F.
ss
ss
s To increase the room temperature:
1 Press set temperature button to set the desired temperature.
A The selected temperature is displayed.
Each time you press the button, the temperature value increases by 2 °F.
Available temperature ranges are as follows:
Cooling & Drying: 65 - 87 °F
Heating: 61 - 83 °F
Automatic: 65 - 83 °F
The display flashes either 47 °F or 97 °F to inform you if the room temperture is
lower or higher than the displayed temperature.
2.4. Selecting a fan speed
1 Press fan speed button to select a desired fan speed.
Each time you press the button, available options change with the display A on
the remote controller, as shown below.
Wireless type Wired type
Display
FAN
SPEED
FAN
SPEED
Available
Option (Fan Speed Switch)
Low-High Low-High
The display and the fan speed of the unit will differ in the following situations:
When STAND BY and DEFROST are displayed.
Just after the heating mode (while waiting to change to another mode).
When the temperature of the room is higher than the temperature setting of the
unit operating in the heating mode.
In Dry mode, where the speed is set automatically and cannot be changed. Only
the display on the remote controller changes.
ON/OFF
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
A
1
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
1
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
B
C
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
A
1
ON/OFF
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
A
1
ON/OFF
TIMER SETSET TEMP.
REMOTE CONTROLLER
MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
TEST RUN
STAND BY
DEFROST
DRY COOL
AUTO FAN
HEAT
CENTRALLY CONTROLLED
˚F
SWING
FAN
SPEED
AUTO
RETURN
NOT AVAILABLE
˚F
CHECK MODE
FILTER
TIMER
TEST RUN
TIMER OFF CLOCKAUTO AUTO
CHECKSET TEMP. STARTSTOP
A
1
BC
ON/OFF TEMP
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
RESETSET CLOCK
MODEL
SELECT
NOT AVAILABLE
SWING
CHECK
FAN
TEST
RUN
˚F
˚C
AMPMSTOP
START
AMPM
COOL
DRY
AUTO
FAN
HEAT
A
1
FAN
FAN