Filter
Top Products
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
3
Figure 9
IMPORTANT
These glass doors utilize tempered glass
which is designed for use with high tempera-
tures but can unexpectedly shatter. DO NOT
SIT CLOSE TO THE GLASS.
Tempered glass will break into small particles if
it should shatter unexpectedly. If the glass
breaks, particles of extremely hot glass could
be discharged into the surrounding environ-
ment, thereby creating a risk of personal injury
or fire. Observation of the above operating
precautions and instructions will reduce the
risk of personal injury or fire.
Extreme temperature changes can cause break-
age — do not build a hot fire and close the
doors if the doors are cold.
If the tempered glass pane becomes scratched
or chipped, it creates a weakness in the glass
which can cause the glass to break when heated.
Replace the pane of glass by contacting your
nearest LHP Distributor. For the name of your
nearest distributor contact:
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
CLEANING
NEVER CLEAN THE GLASS WHEN THE DOORS
ARE HOT. DO NOT USE AMMONIA OR ANY
AMMONIA BASED GLASS OR HOUSEHOLD
CLEANER TO CLEAN THE GLASS OR THE DOOR
FRAME. AN AMMONIA BASED CLEANER WILL
DAMAGE THE FINISH.
Remove dirt and grime from the doors using a
clean dampened towel followed by wiping with
a dry towel. To remove stubborn stains from
the doors, use a mild soap solution and towel to
gently scrub away stain. Take care not to scratch
the glass surface. Do not use abrasive cleaners.
Figure 11
Step 6. Repeat this procedure for the opposite
door assembly.
ADJUSTMENT FOR DOOR ALIGNMENT
The doors are properly adjusted when the top
door trim is in a straight, level line and the gap
between the doors is even at the top and
bottom. If adjustments are required, grasp the
door handle and loosen the lower door hinge
pin using a 3/8" open end wrench*. Slide the
door panel on the hinge pin until the gap
between the upper door trim and upper frame
is even. Retighten the lower door hinge pin*.
Repeat this procedure for the opposite door if
needed.
Hinge Pin
Roller Pin
Upper Door
Guide Track
Pivot
Point
Bottom
Door
Channel
CAUTION: GLASS AND METAL FRAMES GET
HOT — ALWAYS USE HANDLES TO OPEN AND
CLOSE THE DOORS.
Figure 12
GENERAL OPERATING PRECAUTIONS
AND INSTRUCTIONS
CAUTION: THESE GLASS DOORS ARE
LISTED ONLY FOR USE WITH THE SUPE-
RIOR FIREPLACE OR APPLIANCE MODELS
SHOWN. USE ON ANY OTHER FIREPLACE
OR APPLIANCE MAY CONSTITUTE A PO-
TENTIAL FIRE HAZARD.
• Avoid building extremely large fires as the
tempered glass could become damaged.
• Use fireplace tools carefully to avoid striking
the glass.
• Keep wire mesh screens closed during fire-
place use.
• The fireplace flue damper must remain open
until fire is completely out.
• Assure wood and embers are well within the
confines of the grate area and well away from
the glass doors.
• Keep glass doors closed at night when retir-
ing to minimize the loss of heated room air up
the vent.
CAUTION: THE CORNER FIREPLACE OR AP-
PLIANCE SHOULD ONLY BE OPERATED WITH
THE BI-FOLD GLASS DOORS FULLY OPEN OR
FULLY CLOSED (
FIGURE 12
).
Fully Open or
Fully Closed
End Panel
Step 5. Lift and swing the lower corner of the
door over the hole in the bottom door channel
and engage the shorter hinge pin into this hole
(
Figures 10 and 11
).
Figure 10
*Note: Upper door hinge pins can also be
loosened for adjustment purposes; however, it
is easier to loosen lower pins.
Lower Hinge Pin
WARNING: DO NOT BURN TRASH,
CONSTRUCTION SCRAPS, RAILROAD
TIES, OR OTHER HIGHLY-FLAM-
MABLE MATERIAL IN THE FIRE-
PLACE. INTENSE HEAT CAN CAUSE
THE GLASS TO LOSE STRENGTH AND
RESILIENCE WHICH WILL RESULT IN
GLASS BREAKAGE.