Filter
Top Products
INSTR,INST,TMD-90
Linear P/N: 208457 E
Material: 20 Lb. Mead Bond
Size: 8.500" x 11.000"
Ink: Black
Scale: 1-1
Back Side 2 of 2
STEP 9 Walk test. Walk test the unit by walking across the
detection pattern from both sides. The red LED should light as you
cross each detection pattern “finger”. (Alarm transmissions will
occur in walk test.)
STEP 10 Adjust detection pattern. If the detection
pattern is too high or low, loosen the adjustment post and slide
the circuit board up or down.
STEP 11 Program transmitter into receiver. Refer to the
instructions supplied with the supervised receiver to program the
TMD-90 as a non-restoring PIR sensor. Turn the walk test switch
(#6) OFF. Press the TEST button to cause the unit to send a
signal. The TEST button will not send a valid signal if the unit
is in walk test (switch #6 ON).
STEP 12 Replace and lock cover. Replace the unit’s
cover and secure it with the locking screw.
STEP 13 System test. Place the receiver into a sensor test
mode. Stay out of the detection pattern of the PIR for at least
4 minutes then walk across the detection pattern. The receiver
should indicate that the signal was received.
Optional Swivel Mount An optional swivel mount is
supplied for mounting the TMD-90 to a wall in special situations.
Refer to the figure for details on attaching the swivel mount to the
case (swivel mount must be assembled first).
Optional Long Range Lens See the figure for
changing supplied lenses. Do not set the pulse count for more
than 2 pulses when using the long range lens.
Optional Horizontal Curtain Lens See the figure for
changing supplied lenses.
Optional Vertical Curtain Lens See the figure for
details on changing lenses.
Optional Lens Masks Adhesive stick-on labels are
provided to mask unwanted detection areas of each lens. Apply
the labels to the inside of the lens.
SPECIFICATIONS
DETECTOR: Balanced dual-element pyro electric
LENS: Aspheric fresnel lens with 24 facets,
9 main, 8 intermediate, 5 short, 2 creep
DETECTION PATTERN: 40 x 40 feet (12.2 x 12.2 M)
VERTICAL ADJUST: Installer adjustable up and down
SIGNAL PROCESSING: Selectable pulse count (2, 3 & 5 pulses)
Pulse window (8, 16 & 32 seconds)
POWER REQUIREMENTS: Four type “AA” MN1500 batteries
Operating:12 mA maximum
Standby: 15 uA maximum
LED: Extra bright for walk test
RF ENCODING: Linear SX format (A1D PPM @ 200 bps)
NUMBER OF CODES: 16,777,216
TAMPER SWITCH: Switch linked to case cover
SHIELDING: Metal shielding for maximum RFI/EMI immunity
OPERATING TEMPERATURE:
+32° to +122° F
(0° to +50° C)
DIMENSIONS: 5.75" high x 3.25" wide x 1.75" deep
COLOR: Cool Gray 1C
MOUNTING: Wall, corner or swivel
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The
Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers
who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant
this product to consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for
consequential damages arising out of or in connection with use or performance of this product
or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and
implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This
Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC Rules
and Regulations as Part 15 devices. As such, they have limited transmitter
power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time and
may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to acting
as a wholesale distributor or dealer, and these facts should be communicated
to the ultimate users.
Copyright © 2006 Linear LLC 208457 E
WALK ACROSS
DETECTION PATTERN
WATCH RED LED AS
DETECTOR SENSES
MOTION
LOOSEN
ADJUSTMENT
POST TO SLIDE
BOARD
SLIDE BOARD
UP OR DOWN
TO ADJUST
PATTERN
NOTE: BOARD UP
ADJUSTS
PATTERN DOWN
PRESS TEST
BUTTON
TO SEND
SIGNAL
SWITCH #6
MUST BE
OFF
RECEIVER
LEARNS
TRANSMITTER
ID CODE
LOCKING TAB
WILL SNAP SHUT
CLOSE
CASE
INSERT LOCKING
SCREW
1
4
7
*
2
5
8
0
3
6
9
#
?
?
?
A
l
a
r
m
O
p
e
n
B
y
p
a
s
s
L
o
w
B
a
t
t
e
r
y
S
u
p
e
r
v
i
s
o
r
y
T
a
m
p
e
r
T
r
o
u
b
l
e
P
o
w
e
r
WAIT AT LEAST 4 MINUTES BEFORE
WALKING ACROSS THE DETECTION PATTERN!
AFTER WAITING, WALK
ACROSS DETECTION
PATTERN
SYSTEM IN TEST MODE
SHOULD BEEP AS ALARM
SIGNAL IS RECEIVED
SWIVEL
BASE
SHORT
SCREWS (4)
LONG
SCREW (1)
BASE
SWIVEL
BALL
PUNCH OUT
KNOCKOUTS
PRY TABS UP TO
REMOVE LENS
BRACKET
INSERT NEW LENS
WITH SMOOTH SIDE
OUT
6.56'
(2 m)
13.12'
(4 m)
26.24'
(8 m)
52.48'
(16 m)
10.5'
(3.2 m)
14.43'
(4.4 m)
TOP VIEW
SIDE VIEW
131.2'
(40 m)
LONG RANGE LENS
SIDE VIEW
TOP
VIEW
40'
(12.19 m)
3'
(.91 m)
HORIZONTAL
CURTAIN LENS
80'
(24.38 m)
PRY TABS UP TO
REMOVE LENS
BRACKET
INSERT NEW LENS
WITH SMOOTH SIDE
OUT
40'
(12.19 m)
VERTICAL
CURTAIN LENS
TOP VIEW
SIDE
VIEW
4.4'
(1.34 m)
80'
(24.38 m)
PRY TABS UP TO
REMOVE LENS
BRACKET
INSERT NEW LENS
WITH SMOOTH SIDE
OUT
APPLY LENS MASKING
STICKERS TO THE INSIDE
OF THE LENS