Filter
Top Products
INSTR,INST,T-90
Linear P/N: 207138 F
Material: 20 Lb. Mead Bond
Size: 8.500" x 11.000"
Ink: Black
STEP 7 Attach mounting plates. Use the screws or
double-stick tape provided to affix the mounting plates. Be sure
the magnet will be adjacent to the magnet alignment marks.
Mount the magnet no further than 1/2 inch from the transmitter.
Snap transmitter and magnet onto mounting plates.
☞
FOR INTERNAL CONTACTS, SKIP TO STEP 11
STEP 8 Change contact jumper. Remove the side select
jumper and place it on the internal contact disable pins.
STEP 9 Install contact or sensor and transmitter
mounting plate. Mount the external contact or sensor as
described in its instructions. For recessed wiring, drill an
access hole for the wire.
STEP 10 Connect to terminals and set option switch.
Connect two wires from the external sensor to the external
contact terminals. Set the option switches for the type of sensor.
STEP 11 Complete transmitter setup. Set option
switch #2 to enable or disable the 2-minute wait timer. Setting
switch #2 ON enables 2-minute wait timer (after triggering, unit
waits 2 minutes before re-triggering). Switch #3 must be off
when only using the internal contacts.
STEP 12 Close transmitter case. Close the case by
locking the top together first, then snap the bottom together.
STEP 13 Program transmitter into receiver and test.
Follow the receiver’s instructions to set it in a program or learn
mode. Press the bottom of the transmitter case to send a test
signal. Verify that the signal was received and that the transmitter
was properly entered into
the receiver’s memory.
Set the receiver into a
monitor or chime mode.
Open the door or window
monitored by the
transmitter and verify
that the receiver accepts
the alarm transmission.
Close the door or window
and verify that the restore
signal was accepted.
OPTIONAL LONG LIFE BATTERIES To increase the
battery life of the unit in high traffic uses, replace the two type
CR2032 with two DL2450 batteries. Exchange the battery
clamp for the taller one provided, and remove the battery
reduction ring.
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The
Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who
buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if
any. There are no obligations or liabilities on the part of Linear LLC for consequential damages arising
out of or in connection with use or performance of this product or other indirect damages with respect
to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied
warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until
Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties
express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2006 Linear LLC 207138 F
O
P
E
N
1
2
3
4
O
P
E
N
1
2
3
4
OPEN = OFF
TRANSMITTER WILL ACTIVATE
EACH TIME IT IS TRIGGERED
SET SWITCH #2 OFF (OPEN) FOR
LOW ACTIVITY DEVICES (DOOR
SWITCHES, WATER SENSORS,
WINDOW SCREENS, ETC.)
TRANSMITTER CAN ACTIVATE
ONLY ONCE EVERY TWO MINUTES
SET SWITCH #2 ON FOR
HIGH ACTIVITY DEVICES
(MAT SWITCHES, PIR'S, ETC.)
LOCK TOP
TOGETHER
THEN SNAP
CASE SHUT
1
2
1
2
1
2
MOVE JUMPER FROM HERE
(3-PIN SIDE SELECT POSTS)
TO HERE
(2-PIN INTERNAL CONTACT
DISABLE POSTS)
PRESS TO
SEND TEST
SIGNAL
OPEN & CLOSE
DOOR FOR
ALARM & RESTORE
REDUCTION
RING
SHORT
CLAMP
DL2032/CR2032
BATTERIES
SLIDE CLAMP
THROUGH SLOT
DL2450
BATTERIES
TALL
CLAMP
SCREW
*** FOR EXTERNAL CONTACTS ONLY ***
*** FOR EXTERNAL CONTACTS ONLY ***
*** FOR EXTERNAL CONTACTS ONLY ***