Filter
Top Products
READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY
INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC
®
TRACK ITEM.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:26060
0597 Page 2 of 2
FLOATING FEED MOUNTING INSTRUCTIONS
(Flush 26060WH, BK and Standoff 26061WH, BK)
Mounting the CANOPY at some distance away from the end of the
FEED TRACK or FEED CONNECTOR.
NOTE: Hardware is supplied to mount the CANOPY a maximum
of 4 feet from the FEED CONNECTOR. DO NOT EXCEED
THIS DISTANCE.
1. Mark CENTER LINE of TRACK through CENTER LINE of OUT-
LET BOX.
2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET
BOX. The MOUNTING HOLES of the OUTLET BOX should be at
45° to the longitudinal axis of the TRACK. (Fig. 1)
3. Break the BARRIER off the FEED CONNECTOR or FEED TRACK.
(Fig. 6)
4. Remove the DEAD END from the TRACK and retain.
5. Assembly the “U” BRACKET onto the PLATE ASSEMBLY using
the FLAT HEAD SCREW. (Fig. 6)
6. Run the feed wires along the top of the TRACK and into the
FEED CONNECTOR or FEED TRACK. (2 HOTS, 2 NEUTRALS,
AND GROUND; MAXIMUM)
7. NOTE: USE 12 GA. COPPER THHN WIRE INCLUDING
GROUND. IF STRANDED 12 GA WIRE IS USED THE ENDS
MUST BE TINNED.
8. Cut the WIRE COVER to the desired length.
9. Slide the WIRE COVER (over the wires) and PLATE ASSEMBLY
into the TRACK. NOTE THE POSITION OF THE 90° TAB IN
RELATION TO THE FEED-IN POINT. Pass the wires
through the center hole of the PLATE ASSEMBLY.
10. Secure the PLATE ASSEMBLY to the TRACK by tightening the
SCREW. THE WIRE COVER MUST COVER THE ENTIRE
LENGTH OF WIRES ON TOPS OF THE TRACK.
11. Mount the TRACK to the ceiling (see instruction sheet 26000
provided with the track or IS:26478). Positioning the PLATE
ASSEMBLY over the J-BOX.
12. Splice the wires from the track to the wires in the J-BOX.
BLACK TO BLACK, WHITE TO WHITE, AND GROUND TO
GROUND.
13. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with
the MOUNTING HOLES on the J-BOX.
14. Secure the PLATE ASSEMBLY to the J-BOX using the THIN
HEAD SCREWS. (Fig. 7)
15. Attach the GROUND WIRE on the CANOPY PLATE to the
GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 7)
16. WHEN USING THE FLUSH CANOPY 26060WH/BK.
Slide the CANOPY PLATE between the TRACK and CROSS
BAR on the PLATE ASSEMBLY. For added security of CANOPY
PLATE: Drill a hole in CANOPY PLATE and secure to ceiling
with a screw.
17. WHEN USING THE STANDOFF CANOPY 26061WH/BK.
Slide the CANOPY PLATE between the CROSS BAR and NUT
on the PLATE ASSEMBLY. Rotate the NUT to secure the
CANOPY PLATE against the ceiling. (Fig. 8)
18. NOTE: THE CROSSBAR MUST COVER THE SLOT IN
THE CANOPY PLATE AFTER ASSEMBLY.
19. Follow the instructions for wiring on the instruction sheets
included with the the “FEED TRACK” or “CONNECTOR”.
20. Assembly the DEAD END into the end of the TRACK.
FIG. 6
BARRIER
DEAD
END
U BRACKET
90 ° TA B
FLAT HEAD
SCREW
PLATE
ASSEMBLY
WIRE COVER
TRACK UNIT
FEED CONNECTOR
FEED IN POINT
U BRACKET
FIG. 8
TRACK UNIT
J BO X
CANOPY
PLATE
POWER EXTENSION
CONNECTOR
NUT
FIG. 7
CANOPY PLATE
J-BO X
PLATE
ASSEMBLY
WIRE COVER
POWER EXTENSION
CONNECTOR
TRACK UNIT
THIN HEAD
SCREW
CROSS BAR