Filter
Top Products
114A2910B-GB
7-GB
Install Door Control
Locate door control where the garage door is
visible, away from door and door hardware and
out of the reach of children. Mount at least 1,5 m
(5 feet) above the floor.
Serious personal injury from a moving garage
door may result from misuse of opener. Do not
allow children to operate the door control or
remote control transmitter.
Fasten the caution label permanently to the wall
near the door control as a reminder of safe
operating procedures.
There are 2 screw terminals (1) on the back of the
door control (2). Strip about 6mm (1/4") of insulation
from bell wire (4). Separate wires enough to connect
the white/red wire to RED terminal screw 1 and the
white wire to WHT terminal screw 2.
Fasten the door control to an inside garage wall with
sheet metal screws (3) provided. Drill 4mm (5/32")
holes and use anchors if installing into drywall. A
convenient place is beside the service door and out of
reach of children.
Run the bell wire up the wall and across the ceiling to
the garage door opener. Use insulated staples to
secure wire. The receiver quick connect terminals are
located behind the light lens of the opener. Connect
the bell wire to the terminals as follows: white/red to
red and white to white (5).
Operation of the Door Control
Press to open or close the door. Press again to stop
the door while moving.
2
3
1
WHT
2
RED
1
1
1
5
4
LOCK
LIGHT
3
3
2
1
RED
WHT
(Models 800A, 1000A)
(Model 600A)
2
6mm
1
3
2
60 s
120 s
180 s
O
–
21
114A2910B-GB
8-GB
Program your Opener & Remote
Activate the opener only when door is in full view,
free of obstruction and properly adjusted. No one
should enter or leave garage while door is in
motion. Do not allow children to operate push
button(s) or remote(s). Do not allow children to
play near the door.
Your garage door opener receiver and remote control
transmitter are set to a matching code. If you
purchase additional remote controls, the garage door
opener must be programmed to accept the new
remote code.
Program the Receiver to Match Additional Remote
Control Codes:
Using the orange “LEARN” Button:
1. Press and release the orange “learn” button on the
opener. The learn indicator light will glow steadily
for 30 seconds (1).
2. Within 30 seconds, press and hold the button on
the hand-held remote that you wish to operate your
garage door (2).
3. Release the button when the opener light blinks. It
has learned the code. If the light bulb is not
installed, two clicks will be heard (3).
Using the Multi-Function Door Control:
1. Press and hold the button on the hand-held remote
that you wish to operate your garage door (4).
2. While holding the remote button, press and hold the
LIGHT button on the Multi-Function Door
Control (5).
3. Continue holding both buttons while you press the
push bar on the Multi-Function Door Control (all
three buttons are held) (6).
4. Release buttons when the opener light blinks. It has
learned the code. If the light bulb is not installed,
two clicks will be heard (7).
Now the opener will operate when the remote control
push button is pressed. If you release the remote
control push button before the opener light flashes,
the opener has not learned the code.
To Erase all Remote Control Codes:
To deactivate any unwanted remote, first erase all
codes: Press and hold the orange “learn” button on
opener until the learn indicator light goes out
(approximately 6 seconds). All previous codes are
now erased. Reprogram each remote or keyless entry
you wish to use.
3-Channel Remote:
If provided with your garage door opener, the large
button is factory programmed to operate it. Additional
buttons on any rolling code 3-channel remote or
mini-remote can be programmed to operate this or
other rolling code garage door openers.
1
3
2
7
6
L
O
C
K
L
IG
H
T
5
LOCK
LIGHT
4
L
i
f
t
M
a
s
t
e
r
L
i
f
t
M
a
s
t
e
r
1
3
2
60 s
120 s
180 s
O
–
22
Open/Close/Stop Operation
(only if you have a Multifunction door control)
Your remote control can be programmed to operate
one door using all 3 buttons: the left button will only
open the door, the middle button will only close the
door, and the third button will stop the door’s
movement. You may set up this feature as follows:
1. With the door closed, press and hold the left
remote push button.
2. Press and hold the Lock button on the door
control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test
by pressing the left (Open) button on the remote. The
door should open. Press it again while the door is
open and nothing should happen. Press the middle
(Close) button and the door should close. Press the
third (Stop) button while the door is moving and it
should stop immediately.
23
Open
Close
Sto
p