Lennox Hearth MP-36OD Door User Manual


 
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
ADJUSTMENT FOR DOOR ALIGNMENT
The doors are properly adjusted when the top door trim is in a straight,
level line and the gap between the doors is even at the top and bottom. If
adjustments are required, grasp the door handle and loosen the lower
door pivot pin using a ³⁄₈" open end wrench*. Slide the door panel on the
hinge pin until the gap between the upper door trim and upper frame is
even. Retighten the lower door pivot pin*. Repeat this procedure for the
opposite door if needed.
*Note: Upper door pivot pins can also be loosened for adjustment
purposes; however, it is easier to loosen lower pins.
GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS
CAUTION: THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH
THE FIREPLACE OR APPLIANCE MODELS SHOWN ON THE FRONT
PAGE. USE ON ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTI-
TUTE A POTENTIAL FIRE HAZARD.
Avoid building extremely large fires as the tempered glass could
become damaged.
Use fireplace tools carefully to avoid striking the glass.
Keep wire mesh screens closed during fireplace use.
The fireplace flue damper must remain open until fire is completely out.
Assure wood and embers are well within the confines of the grate area
and well away from the glass doors.
Keep glass doors closed at night when retiring to minimize the loss of
heated room air up the vent.
IMPORTANT: THE FINISH OF THESE DOORS MAY BE PROTECTED WITH
A SELF ADHERING PLASTIC COATING THAT MUST BE REMOVED
BEFORE HEAT IS GENERATED BY A FIRE IN THE FIREBOX. TO PREVENT
MELTING, ENSURE THAT ANY PLASTIC COATING PROTECTING THE
FINISH OF THESE DOORS IS REMOVED FOLLOWING INSTALLATION.
REFER TO THE FIREPLACE INSTALLATION AND HOMEOWNER'S IN-
STRUCTIONS FOR DETAILED INSTRUCTIONS REGARDING THE MAIN-
TENANCE OF THE FINISH OF THESE DOORS.
CAUTION: GLASS AND METAL FRAMES GET HOT — ALWAYS USE
HANDLES TO OPEN AND CLOSE THE DOORS.
CLEANING
NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT. DO NOT USE
AMMONIA OR ANY AMMONIA BASED GLASS OR HOUSEHOLD CLEANER
TO CLEAN THE GLASS OR THE DOOR FRAME. AN AMMONIA BASED
CLEANER WILL DAMAGE THE FINISH.
Remove dirt and grime from the doors using a clean dampened towel
followed by wiping with a dry towel. To remove stubborn stains from the
doors, use a mild soap solution and towel to gently scrub away stain.
Take care not to scratch the glass surface. Do not use abrasive cleaners.
IMPORTANT: THESE GLASS DOORS UTILIZE TEMPERED GLASS
WHICH IS DESIGNED FOR USE WITH HIGH TEMPERATURES BUT CAN
UNEXPECTEDLY SHATTER. DO NOT SIT CLOSE TO THE GLASS.
Tempered glass will break into small particles if it should shatter
unexpectedly. If the glass breaks, particles of extremely hot glass could
be discharged into the surrounding environment, thereby creating a risk
of personal injury or fire. Observation of the above operating precautions
and instructions will reduce the risk of personal injury or fire.
Extreme temperature changes can cause breakage do not build a hot
fire and close the doors if the doors are cold.
If the tempered glass pane becomes scratched or chipped, it creates a
weakness in the glass which can cause the glass to break when heated.
Replace the pane of glass by contacting your nearest distributor or
dealer.
Figure 4
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Printed in U.S.A. © 2002 by Lennox Hearth Products
P/N 750,141M REV. B 06/2006
Pivot Pin
Roller Pin
Upper Door
Guide Track
Spring Clip
Figure 3
CAUTION: THE FRONT-OPEN FIREPLACE OR APPLIANCE SHOULD
ONLY BE OPERATED WITH THE GLASS DOORS FULLY OPEN OR FULLY
CLOSED.
CAUTION: MULTI-OPEN FIREPLACES MUST BE OPERATED WITH THE
GLASS DOORS FULLY CLOSED.
Fully Open or
Fully Closed
Front-Open Systems
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
1110 West Taft Avenue
Orange, CA 92865
WARNING: DO NOT BURN TRASH, CONSTRUCTION SCRAPS,
RAILROAD TIES, OR OTHER HIGHLY-FLAMMABLE MATERIAL
IN THE FIREPLACE. INTENSE HEAT CAN CAUSE THE GLASS TO
LOSE STRENGTH AND RESILIENCE WHICH WILL RESULT IN
GLASS BREAKAGE.