Filter
Top Products
New 3/07
2
755660ES
7
755660ES
New 3/07
FUNCIONAMIENTO (Figura 1 a 3)
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una supercie rme y plana.
CUIDADO: Los tacos de plástico o hule, tales como las patas
de esta unidad, pueden pegarse a la supercie de los muebles y/o
a los pisos de madera. La unidad podría dejar un residuo capaz de
oscurecer, manchar o dejar marcas permanentes en el acabado de
ciertas supercies de muebles, incluyendo supercies de madera
y/o pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje rmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes en
este estado podrían sobrecalentarse y representar
un peligro de incendio grave; si queda cubierto por
una cortina o tela, el peligro de incendio es todavía
mayor.
4. Cuando el Calefactor se conecte por primera vez, se oirá un “bip” y
la Luz de Encendido se encenderá indicando que hay electricidad
en la unidad. La Luz de Encendido permanecerá encendida hasta
que el Calefactor sea desconectado del tomacorriente eléctrico.
5. ENCIENDA el Calefactor oprimiendo el Botón de Encendido ( ).
6. Cuando se lo encienda por primera vez, el Calefactor mostrará
la temperatura actual de la habitación en ° Fahrenheit. Oprima
los botones ( ) y ( ) al mismo tiempo para cambiar la pantalla a
° Celsius. Oprima los dos botones al mismo tiempo nuevamente
para cambiar la pantalla y volver a ° Fahrenheit.
7. Al encender el Calefactor, la unidad estará en calor ALTO ( ) (1500
vatios) y mostrará la temperatura actual de la habitación (Figura 1)
8. Oprima el botón ( ) para calor BAJO ( ). (900 vatios)
9. Para APAGAR el Calefactor, presione el Botón de Encendido
( ) y desconecte el Calefactor del tomacorriente eléctrico.
Función de Oscilación:
Presionar el Botón de Oscilación (OSC) permitirá al Calefactor
oscilar hacia atrás y hacia delante. Para detener la oscilación, oprima
el Botón de Oscilación (OSC) una vez más.
Función de Temporizador (Figura 2)
La función de temporizador puede ser activada cuando la pantalla
del Calefactor está en cualquier función o velocidad. Esta función
le permite fijar la cantidad de tiempo que el Calefactor estará
funcionando antes de apagarse automáticamente, de 1 hora a 8 horas.
Presionar el Botón de Temporizador ( ) aumentará la cantidad de
tiempo en 1 hora cada vez que dicho botón sea oprimido. Después
que la pantalla reeje 8 horas, si presiona el Botón de Temporizador
( ) una vez más, se reiniciará el Calefactor para función continua.
MODELO 755660
El Calefactor se apagará cuando el tiempo jado haya transcurrido.
La unidad puede ser encendida nuevamente presionando el Botón
de Encendido ( ).
CONTROL AUTOMÁTICO DE TEMPERATURA (Figura 3)
Oprimir el botón ( ) o el botón ( ) le permite a usted fijar la
temperatura deseada del Calefactor.
1. Cuando el botón ( ) o el botón ( ) esté presionado, la pantalla
exhibirá la temperatura jada y el símbolo ( ) aparecerá.
2. Oprima el botón ( ) para aumentar la temperatura fijada
deseada o presione el botón ( ) para reducir la temperatura
jada deseada.
3. Cuando la temperatura del aire alcance los 2° por encima de la
temperatura jada, el Calefactor se apagará.
4. Cuando la temperatura del aire alcance un 1° por debajo de la
temperatura jada, el Calefactor se encenderá.
5. Esta función se cancelará si el botón ( ) es oprimido y el
Calefactor ahora estará en calor Alto ( ).
NOTA: Es normal que el “ventilador” del calefactor funcione durante
aproximadamente 5 segundos después que el calefactor se haya
apagado tras alcanzar la temperatura.
Figura 1
Pantalla al ser encendido por primera vez
Función de
Temporizador en
Calor BAJO
Función de Temporizador
en Calor Alto y Control
Automático de Temperatura
Figura 2
Figura 3
La pantalla reeja calor Alto y Función de Control
Automático de Temperatura
El gancho del control remoto está ubicado en la parte posterior del
calefactor. (Figura 4)
Figura 4
Vista Posterior del Calefactor
1. DO NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MUL-
TIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE
HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
2. AVOID THE USE OF EXTENSION CORDS BECAUSE THE EXTENSION CORD MAY OVERHEAT AND CAUSE A RISK OF FIRE.
HOWEVER, IF YOU HAVE TO USE AN EXTENSION CORD, MINIMIZE THE RISK OF OVERHEATING BY USING THE SHORTEST
CORD POSSIBLE AND BY ENSURING THAT IT IS UL LISTED. THE CORD SHALL BE A 3-WIRE, GROUNDING TYPE, WITH NO. 14
AWG MINIMUM SIZE AND RATED NOT LESS THAN 1875 WATTS (15A). NEVER USE A SINGLE EXTENSION CORD TO OPERATE
MORE THAN ONE HEATER. NEVER USE A CORD REEL.
WARNING: Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug fits tightly into outlet
before each use. During use, check to make certain the Heater plug is not overheating. If necessary have a qualied electrician
check and/or replace the wall outlet.
3. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause re, electrical shock,
or injury to persons.
4. Make certain that the room is equipped with a working smoke detector.
5. Make certain that the power source conforms to the electrical requirements of the Heater.
6. Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left
operating unattended.
7. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to t in
a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied electri-
cian. Do not attempt to defeat this safety feature.
8. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
9. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
10. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
11. Do not insert or allow ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, re, or dam-
age the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
12. To prevent a possible re, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings
may become blocked.
13. Always place the Heater on a stable, at, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power
Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with
throw rugs, runners, or the like. Arrange Power Cord away from room trafc and where it will not be tripped over.
14. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater.
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the
Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
15. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or ammable liquids are
used or stored. DO NOT use Heater in locations where ammable or explosive chemicals are stored, or in wet atmospheres. This Heater
is intended for general use ONLY.
16. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
17. DO NOT use Heater outdoors.
18. Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs,
move the Heater to another location.
19. Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.
20. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are conned. Please
refer to National Electric Code (NEC) Article 547-7 (2002), or applicable state or local codes or standards relating to electrical require-
ments for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2002).
21. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE
REQUIREMENTS OF NEC ARTICLE 500 (2002).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the
risk of re, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND
UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE
HEATER IS ON OR PLUGGED IN.
SAVE THESE INSTRUCTIONS