Filter
Top Products
Función de Temporizador
FUNCIONAMIENTO (Figuras 1 a 3)
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
CUIDADO: Los tacos de plástico o hule, tales como las patas
de esta unidad, pueden pegarse a la superficie de los muebles y/o
a los pisos de madera. La unidad podría dejar un residuo capaz de
oscurecer, manchar o dejar marcas permanentes en el acabado de
ciertas superficies de muebles, incluyendo superficies de madera
y/o pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes en
este estado podrían sobrecalentarse y representar un
peligro de incendio grave; si queda cubierto por una
cortina o tela, el peligro de incendio es todavía mayor.
4. Cuando el Calefactor se conecte por primera vez, se oirá un
“bip” y la Luz de Encendido se encenderá indicando que hay
electricidad en la unidad. La Luz de Encendido permanecerá
encendida hasta que el Calefactor sea desconectado del
tomacorriente eléctrico.
5. ENCIENDA el Calefactor oprimiendo el Botón de Encendido.
6. Cuando se lo encienda por primera vez, el Calefactor estará en
calor Alto (1500 vatios) en Máx. (La luz Alta estará encendida
permanentemente y la luz de Máximo estará titilando).
7. Oprima el Botón de Encendido una vez más y el Calefactor
estará en Calor Bajo indicado por la luz permanente junto a Bajo.
8. Oprimir el Botón de Encendido por tercera vez APAGARÁ
el Calefactor.
9. Cuando el Calefactor está APAGADO, la luz roja en la parte
frontal del Calefactor permanecerá encendida hasta que el
Calefactor sea desconectado del tomacorriente eléctrico.
Función de Oscilación
1. Presionar el Botón de Oscilación (OSC) permitirá al Calefactor
oscilar hacia atrás y hacia delante. Para detener la oscilación,
oprima el Botón de Oscilación (OSC) una vez más.
Función de Temperatura (Figura 2)
La función de temperatura automática sólo operará en calefac-
ción “Alta”. No puede fijar la temperatura automáticamente
cuando la unidad se encuentre en la modalidad de calefacción baja.
1. Para fijar una temperatura específica en la habitación, presione
el botón de temperatura hasta la configuración deseada. La
luz de la temperatura escogida continuará titilando hasta que
la habitación alcance la temperatura deseada. El Calefactor
realizará el ciclo de apagado y encendido para mantener la
temperatura de la habitación. Cuando se fija en MAX (Máximo),
el Calefactor operará continuamente.
Rev. E 3/11
2
751320ES
7
751320ES
Rev. E 3/11
MODELO 751320
CONTROL REMOTO
Todas las funciones ejecutadas con el Control Remoto funcionan
idénticamente a los controles manuales, solo que usted debe
presionar el botón para alcanzar la temperatura máximo.
(Figura 4)
1. Instale las dos baterías “AAA”.
2. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas,
estándar (carbono-zinc) o recargables (níquel-cadmio).
3. NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS
PUEDEN ESTALLAR O PUEDEN SALIRSE.
+
+
Figura 4
Si usted pierde su mando a distancia, por favor Cliente de llamada
Serive para ordenar un reaplacement en 1-800 -233-0268, de lunes
a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este
de los Estados Unidos).
Figura 1
Pantalla al ser encendido por primera vez
Luz de Encendido
Función de Temporizador (Figura 3)
1. La Función de Temporizador puede ser activada cuando la
pantalla del Calefactor se encuentre en cualquier velocidad
o temperatura. Esta función le permite a usted seleccionar la
cantidad de tiempo que el Calefactor estará en funcionamiento
antes de apagarse automáticamente, de 1 hora a 7 horas. Oprimir
el Botón de Temporizador aumentará la cantidad de tiempo, en
combinaciones de 1,2 y 4 horas. Oprimir el botón continuamente
resultará en que el temporizador quede fijado para un lapso de
7 horas. El Calefactor se apagará cuando el tiempo fijado haya
transcurrido. La unidad puede ser apagada oprimiendo el Botón
de Encendido. NOTA: Cuando el botón de temperatura esté
colocado en la posición MAX, la unidad se apagará cuando
el período de tiempo haya expirado.
Función de Temperature
Figura 2
Figura 3
Vista de frente del
Control Remoto
Vista posterior del
Control Remoto
1. ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG HEATER
INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL
OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL
OUTLET ONLY.
WARNING: FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY
INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A
QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET.
2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury
to persons.
3. Make certain that the room is equipped with a working smoke detector.
4. Make certain that the power source conforms to the electrical requirements of the Heater.
5. Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating
unattended.
6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polar-
ized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
7. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. Please
contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
8. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
9. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
10. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the
Heater. Do not block or tamper with the Heater in any manner while it is in operation.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become
blocked.
12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so
the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or
similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep com-
bustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them
at least 1 foot (0.3 m) from the sides and rear.
14. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored.
DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This Heater is intended for general use
ONLY.
15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
16. DO NOT use Heater outdoors.
17. Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move the
Heater to another location.
18. Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.
19. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the
receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.The user is cautioned that changes and
modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
20. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to
National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for
Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
21. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes
or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF
NEC ARTICLE 500 (2008).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk
of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND
UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE
HEATER IS ON OR PLUGGED IN.
SAVE THESE INSTRUCTIONS