Filter
Top Products
Rev. A 9/07
2
2250QMES
Rev. A 9/07
7
2250QMES
MODELO 2250QM
CONTROLE LA ASAMBLEA DE CAJA (Figura 1)
LA CAJA DEL CONTROL DEL VENTILADOR DEBE
SER MONTADA AL SOPORTE ANTES DE UTILIZAR EL
VENTILADOR.
1. Cuidadosamente retire el Ventilador de la bolsa plástica y la caja.
2. Coloque el ventilador sobre una supercie rme y nivelada.
ADVERTENCIA: Los tacos de plástico o hule, tales como las
patas de esta unidad, pueden pegarse a la supercie de los muebles.
La unidad podría dejar un residuo capaz de oscurecer, manchar o
dejar marcas permanentes en el acabado de ciertas supercies de
muebles, incluyendo supercies y pisos de madera.
3. Remover el tornillo de sujeción de la parte trasera de la caja
de control del ventilador.
4. Asegurarse de que el alambre de la caja de control del ven-
tilador al motor está entre la parta del pedestal y la rejilla tal
como se muestra.
5. Insertar el tornillo de sujeción de la parte trasera del ventilador a
travez del oricio en la pata del pedestal tal como se muestra.
6. Alinear la caja de control del ventilador con el
tornillo de sujeción.
7. Apretar el tornillo de sujeción con la mano. No lo
aprete demasiado.
8. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje
rmemente en el tomacorriente.
Cuando los enchufes quedan ojos en los tomacorrientes,
pueden deslizarse parcial o completamente fuera
del tomacorriente con un leve movimiento del cable
adosado. Los tomacorrientes en este estado podrían
sobrecalentarse y representar un grave peligro de
incendio; si está cubierto por una cortina o tela, el
riesgo de incendio es aún mayor.
9. Encienda el Ventilador seleccionando la velocidad deseada con
la Perilla de Encendido situada al costado del Ventilador.
0 – Apagado
3 – Alta
2 – Media
1 – Baja
10. Para ajustar el ángulo vertical, mueva el cuerpo del Ventilador
hacia delante o hacia atrás hasta la posición deseada.
QUICKMOUNT
®
DEL SOPORTE PARA LA PARED
1. Escoja una ubicación que monta que permitirá la instalación de
hardware (no suministró) directamente en sementales de pared
ni apoyo estructural adecuado.
2. Utilizar el paréntesis de pared como una plantilla, marca las ubica-
ciones de hoyo en la pared después de nivelar el paréntesis.
3. Abroche paréntesis de pared a montar supercie que utiliza 4 cierres
calibrados apropiados. Taladre hoyos pilotos como sea necesario.
(Vea la Figura 2).
El CUIDADO: Verique para eléctrico y/o las líneas de gas antes de
instalar el paréntesis de pared.
COLGANDO EL VENTILADOR EN EL SOPORTE
PARA LA PARED
1. Sostenga el ventilador en una posición vertical, como si estuviera sobre
en el suelo.
2. Coloque el borde trasero del pedestal en los ganchos del soporte para
la pared.
Su ventilador puede ser armado en la pared usando el
nuevo soporte para la paed de montaje rápido suminis-
trados con su ventilador. (Figuras 2 y 3)
QUICKMOUNT
®
SYSTEM
Figura 2
Figura 1
Figura 3
5/16" Tornillo X de la Demora 2" Largo (el mínimo)
16”
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to re-
duce the risk of re, electrical shock and injury to persons, including the following:
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
1. Make certain the power source conforms to the electrical requirements of the Fan.
2. Make certain that the room is equipped with a working smoke detector.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause re, electrical shock, or
injury to persons.
4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5. Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6. This Fan must NOT be used in potentially dangerous locations such as ammable, explosive, chemical-laden or wet atmospheres where
gasoline, paint or ammable liquids are used or stored.
7. DO NOT use Fan in or near a window. Rain may create an electrical hazard.
8. Completely assemble Fan, according to instructions, before connecting to power supply.
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
9. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a re. If you must use an extension
cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed. NEVER use a single extension
cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord reel, surge protec-
tor, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a re hazard.
10. NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. There
are no user serviceable parts. Return Fan to an authorized service facility for examination, electrical or mechanical adjustment or repair.
11. NEVER insert or allow ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or re, or
damage the Fan. To reduce the risk of re, DO NOT block or tamper with the Fan in any manner while it is in operation.
12. Always place the Fan on a stable, at, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power Cord
so the Fan or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs,
runners or the like. Arrange Power Cord away from room trafc and where it will not be tripped over.
13. This Fan is not intended for use in wet or damp locations. NEVER locate a Fan where it may fall into a bathtub or other water container.
NEVER use Fan where ammable liquids are used or stored.
14. NEVER use Fan outdoors.
15. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are conned. Please refer
to National Electric Code (NEC) Article 547-7 (2002), or applicable state or local codes or standards relating to electrical requirements for
Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIRMENTS OF NEC ARTICLE 547-7 (2002).
16. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local
codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE REQUIRMENTS OF
NEC ARTICLE 500 (2002).
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching recep-
tacle. Under no circumstances should the grounding prong be cut off the plug. Where a two-prong wall
receptacle is encountered, it must be replaced with a properly grounded three-prong receptacle installed
in accordance with the National Electrical Code (NEC) and all applicable local codes and ordinances. This
work must be done only by a qualied electrician, using copper wire only.
This plug is a safety feature, to reduce the risk of re, electric shock and personal injury. DO NOT remove,
replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due
to the safety device incorporated in this plug. Return to an authorized service center or call 800-233-0268,
Monday - Friday, between 8:00 a.m. and 5:00 p.m. EST. If the plug warning label is missing or damaged, call
the toll free number for a replacement label.
3. Permita que el pedestal gire hacia abajo de modo que los pies
de goma delanteros se apoyen en la pared debajo del soporte de
montaje.
4. Incline la cabeza del ventilador a la posición deseada.