Kenmore 100 625.388150, 150 625.388160 Water System User Manual


 
CARE OF YOUR WATER SOFTENER
SECTION 3

3UREOHPV 4XHVWLRQV" &DOO    .HQPRUH :DWHU /LQH
D. CHECKLIST ... TO HELP YOU SAVE MONEY
,I \RXU ZDWHU VRIWHQHU IDLOV WRZRUN PDNH WKH IROORZLQJ HDV\ FKHFNV 2IWHQ \RX ZLOO ILQG ZKDW·V ZURQJ \RXU
VHOI DQG \RX ZRQ·W KDYH WR FDOO DQG ZDLW IRU VHUYLFH ,I \RX GR QRW ILQG DQ\WKLQJ ZURQJ ZKLOH PDNLQJ WKH
FKHFNV DQG \RXU VRIWHQHU VWLOO GRHV QRW ZRUN FDOO .HQPRUH :DWHU /LQH DW 
1RWH
 $OVR UHDG (5525 &2'( SDJH 
 ,I DQ HUURU FRGH LV QRW GLVSOD\HG SUHVV DQG KROG WKH 6(/(&7 EXWWRQ XQWLO WKH GLVSOD\ FKDQJHV 7KHQ SUHVV
WKH 6(/(&7 EXWWRQ DJDLQ DQG KROG XQWLO D IODVKLQJ 65 FRGH DSSHDUV ,W PXVW VKRZ 65 IRU 8OWUD6RIW  RU
65 IRU 8OWUD6RIW  ,I DQ\ RWKHU QXPEHU VKRZV WKH IDFHSODWH FRPSXWHU LV ZRUNLQJ RQ LQFRUUHFW LQSXW DQG
ZRXOG SUREDEO\ EHWKH FDXVH RI WKH SUREOHP 7RVHW65RU 65 SUHVV HLWKHUWKH 83
RU '2:1 EXWWRQ
:KHQ WKH FRUUHFW PRGHO FRGH VKRZV SUHVV 6(/(&7 WR UHWXUQ D IODVKLQJ  $0 GLVSOD\ 5HVHW WKH SUHVHQW
WLPH KDUGQHVV QXPEHU HWF SDJHV  DQG 
PROBLEM CAUSE CORRECTION
1R VRIW ZDWHU No salt (or salt bridged) in the storage tank Refill with salt, or break the salt bridge (page
3-1). Press ON/OFF-HOLD (RECHARGE
NOW) button and hold for 3 seconds to start a
regeneration (see page 2-1).
Transfomer unplugged at the wall outlet,
or power cable leads loose, fuse blown,
circuit breaker popped, or circuit switched
off.
Check for loss of power due to any of these
and correct. With the power back on, look at
the time display and read PROGRAM
MEMORY, page 2-1.
Manual bypass valve(s) in bypass position Look at FIG.14 on page 4-1. Move the stem in
a single valve to service. In a 3-valve bypass,
open the inlet and outlet valves, and be sure to
fully close the bypass valve.
Dirty, plugged or damaged nozzle &
venturi
Take apart and clean or replace damaged
parts (see page 3-2).
Valve drain hose plugged The drain hose must not have kinks, sharp
bends, or be raised too high above the
softener (see page 16 in your
LQVWDOODWLRQ
PDQXDO
).
:DWHU KDUG VRPHWLPHV Hardness number setting too low Press and release the SELECT button until
HARDNESS shows in the display. Read the
hardness number in the display and be sure
the same grains per gallon number is shown
on your water analysis report. See page 1-4 to
reset. Press and release the SELECT button
until the present time shows in the display.
Incorrect SR code selected. See above.
Using hot water when softener is
regenerating
Avoid using hot water duringthis timebecause
the water heater refills with hard water (see
Automatic Bypass, page 2-4).
Increase in the grains of hardness in your
water supply
Ask your Sears retail store for a new water
analysis. Then make a new hardness number
setting (page 1-4).
%ULQH WDQN IORRGHG Restricted drain line Check for kinks, bends or obstructions (see
page 16 in your LQVWDOODWLRQ PDQXDO).
Plugged or dirty nozzle & venturi Take apart and clean or replace damaged
parts (see page 3-2).
Valve-rotor disc & seals Check for scratches or grooves, replace if
needed.