Filter
Top Products
Flexible Tubing to Hard Piping Installation
Instructions – for Motor/Pump Part# 055173
Continued
Page 2 of 2
Operation #2 Re-Assembly
Notes:
1. Remove filter tub from motor/pump housing assembly and set
aside. On 18, 20 and 24 models only, remove pipe nipple 3/8”
NPT x 1” and discard. Replace with pipe nipple 3/8” NPT x 1-
1/2” (item B). See view A for proper dimensions from back of
sump to front of quick connect. On 14” filter tub, see view A
for proper dimesions from back of sump to front of quick dis-
connect. Place the filter tub into the filter cart assembly.
Release the filter tub away from the pump housing as shown
in side view. Turn the entire assembly upside down as shown
in view B. This step is critical to insure proper alignment
between the motor housing quick connect and the filter tub
quick connect. Use table or bench, making sure the
motor/pump housing is off of the table/bench.
CAUTION: IF FILTER ASSEMBLY IS PLACED UPSIDE DOWN
ON A TABLE OR BENCH, MAKE SURE UNIT IS SECURE, SO
AS NOT TO SLIDE OFF TABLE/BENCH.
2. Slide item C into position to connect the compression fitting on
the pump’s 90° fitting. DO NOT
TIGHTEN COMPRESSION
FITTING AT THIS TIME. Attach item C, to the pump housing
with items D and E. DO NOT TIGHTEN COMPLETELY AT
THIS TIME. Play must be present for proper alignment of
pump housing connect and filter tub quick connect. Slide the
filter tub assembly forward until the quick connects are
engaged. Tighten items D and E completely. Tighten compres-
sion on item C. Remove (2) bolts and washers “K” and add
reinforcement bracket “L.” Use longer (2) bolts pro-
vided and discard old ones. For 20 and 24 models,
add items D and K to reinforcement bracket and
tighten until snug on motor mount housing assem-
bly (See Bottom View).
3. Attach filter tub pull rod handle using item
F and I.
4. Attach the pump mount covers using item G.
5. Inspect for spacers between casters and filter
cart assembly. If none are present, remove
casters and place item J (2) on the casters
threaded stem and reassemble using existing
fasteners and item I.
6. Carefully turn filter assembly to the upright posi-
tion. Release the filter tub pull rod and check for
proper disconnect. Reconnect the filter tub to
the motor mount housing using handles. If the
assemblies do not connect properly, it will be
necessary to verify notes above were followed
correctly.
7. Fill filter tub with oil per users manual, cycle oil
to check for leaks at fittings, correct if needed.
Your Kit Includes (items with * may not be included):
Item Part # Qty Description
A --------- - ------------------------
*B 056990 1 Pipe Nipple 3/8 NPT 1-1/2 SS-304
C 056907 1 Bracket Ass’y Haight Baker Pump
D 020101 8 Nut 5/16 Hex Head Serrated Flang
E 017142 4 Screw 5/16-18 x 3/4 Hex Head
F 015227 2 Nut 1/4” Acorn S/S
G 004611 4 Screw #10 x 3/8 Sheet Metal Pan HD.
*I 037672 A/R Sealant Locktite 262 (.017 oz.)
J 056765 8 Washer Flat 7/16” ID x 1.00 OD x .078 THK.
K 017481 4 Screw 5/16 -18 x 1-3/4 Hex HD SS
L X 1 Reinforcement Bracket
M 015158 2 Acorn Nut 5/16-18 SS
N 052733 2 Washer 11/32 ID x 3/4 OD
O 000290 2 Washer, Lock 5/16” Spilt
Pump Mount Cover
G See Note #4
Motor Mount Housing Assembly
Filter Tub Assembly
Filter Cart Frame Assembly
L
See Note #2
See Note #1
Filter Tub Connected
Side V
iew
Bottom View
Mount Reinforcement
Bracket as Shown
L
Bolts
Must Be
Flush Not
Tight
C
K&D Bolts Only
for Models 20”
and 24” See
Note #2
J&I See
Note #5
Filter Tub
Pull Rod
See Note #3
K,M,N,O
F&I See
Note #3
B
D&E
Support Filter Tub As
Shown to Remove Any
Play Between Tub and
Filter Cart.
Item ‘C’ Detail
Filter Tub Disconnected
V
iew B
See Note A
V
iew A
Table or Bench
2-5/8”
Note A Dimensions
9-5/16” for 14” Filter
11-3/8” for 18” Filter
12-3/8” for 20” Filter
14-3/8” for 24” Filter