Filter
Top Products
4
Using Your Kambrook Jaguar
Vacuum Cleaner
Remove all packaging from the unit, hose
and other accessories; ensure that you
have removed all of the accessories before
discarding the packaging.
Ensure that the dust bag and filters are
correctly fitted.
Locate the crush proof hose and push the
connection point into the hose inlet
connection on the top of the unit, until a
“click” sound is heard.
Connect the wide end of the metal wand
to the hose end, and push together firmly.
Fit the floor tool to the narrow end of
the wand/s and push together firmly.
Fully extend the power cord by pulling
the power plug (situated at the rear of the
unit) out from the unit, until the yellow
tape on the cord is shown.
ENSURE THAT YOU DO NOT
OVER EXTEND THE POWER
CORD – DO NOT EXTEND PAST
THE RED WARNING TAPE ON
THE CORD
Plug into a 230/240v power point and
switch the power on.
To commence vacuuming push down on
the on/off foot pedal, at the top, rear of
the unit.
When vacuuming is complete, push down
on the ‘on/off’ pedal to switch off.Turn
the power off at the outlet and then
remove the power cord from the power
outlet (when removing plug from the
power outlet grasp the plug not the cord).
To retract the cord push down on the
‘cord rewind’ pedal.
IMPORTANT: HOLD THE PLUG END
WHEN RETRACTING THE CORD TO
PREVENT IT FROM STRIKING YOU OR
THE VACUUM.
ALWAYS ENSURE THAT THE
DUST BAG AND THE MOTOR
PROTECTION FILTER ARE
CORRECTLY FITTED. NEVER
OPERATE WITHOUT THE DUST
BAG AND FILTERS IN PLACE.
Variable Power Control
The variable power control slide switch is
located on the top of the vacuum cleaner.
Slide the control to the rear for maximum
power for vacuuming hard floor and
carpet surfaces. Slide the control to the
front at the minimum power level when
using the crevice and brush tools.
Crevice and brush tool accessories
The crevice tool is ideal for vacuuming
hard to reach places such as the edges
along skirting boards.
The brush tools can be used to vacuum
delicate surfaces and areas such as shelves
and venetian blinds.
Set the variable speed control between
minimum and medium power when using
the tool accessories.
Turn off the vacuum cleaner when
changing any attachments.
Dust bag indicator and changing the
dust bag
You have the option of using a Cloth bag
or a paper dust bag.
The dust bag should be changed when full.
5
The dust bag indicator window will
gradually turn red as the bag fills up and
when the dust bag indicator displays ‘red’
it is time to change the dust bag.
Always switch appliance off, then switch
off at the power outlet and unplug the
appliance prior to replacing dust bags or
filters.
To remove the dust bag, ensure the unit is
down on its wheels, remove the crush
proof hose and push the ‘Dust bag
compartment lid release lever’ underneath
the handle. Once the lid has released, pull
the top cover back.
To remove the bag, grasp the top of dust
bag and pull out. If you are using the cloth
bag dispose the dust in a rubbish bin. If
you are using a paper dust bag you can
dispose the bag with its contents in the
rubbish bin.
To place a new dust bag, take a fresh dust
bag and with the arrow (printed on the
material section of the dust bag) pointing
down slide the material down into the
dust bag holder, until it comes in contact
with the bottom of the holder.
HINT: once the bag is inserted ‘puff-out’ the bag as
much as possible to ensure the full capacity of the
bag can be taken up.
When vacuuming fine dust particles, the
fine dust particles can clog the pores of
the dust bag and the dust bag indicator
will indicate full. If this happens the bag
could appear relatively empty, however
the bag will still need to be changed to
avoid strain on the motor.
NOTE:The bag compartment lid may not close if
the bag is not correctly fitted.
IMPORTANT: DO NOT USE THE
UNIT WITHOUT A DUST BAG IN
PLACE
Replacing filters
Filters must be cleaned from time to time
to remove the fine dust particles that have
been collected.This can be done by
shaking them; however after
approximately 5 dustbag changes the
filters should be replaced.
Motor protection filter
The motor protection filter must always
be in place when operating the vacuum
otherwise damage to the motor may
occur
To replace the motor protection filter –
Remove the dustbag or pull the bag
forward.The motor protection filter is
located at the rear, right hand side of this
inner chamber. Pull the plastic filter holder
upward to remove.
Dust bag holder
Filter holder
Filter holder
Removable filter