Kambrook KRH300 Electric Heater User Manual


 
8 9
Setting the Heating Mode
and Variable Temperature
To control the heater, turn the Heat
Setting dial and Variable Thermostat
dial as follows.
The Heat Setting dial has 5 modes:
0 - Shuts off the heater
1 - Low (600 watts)
2 - Med (1200 watts)
3 - Med-High (1800 watts)
4 - High (2400 watts)
The Variable Thermostat dial acts
as an automatic thermostat and
can be used to maintain your desired
temperature.
Turn the Heat Setting dial to setting 4
and the Variable Temperature dial to
‘MAX’ setting. Once a comfortable
room temperature has been reached,
slowly turn the Variable Temperature
dial anti-clockwise until a click sound
is heard.
NOTE: The Variable Thermostat
control will only operate if the
heat setting is set to heat setting
3 or 4.
At this setting your heater will
automatically cycle on and off
to maintain the desired room
temperature
Turn the heater off by turning the Heat
Setting dial to 0 position.
The Heat Indicator Light will illuminate
when the heater is turned to any Heat
Setting from 1 to 4. It will turn off when
set to 0.
NOTE: This heater features a
tipover switch. If the heater
tips over, the quartz heating
elements will automatically
switch off. The power indicator
light remains on. Once placed
back into the upright position,
the quartz heating element will
automatically switch on again.
ThermoGuard Overheating
Safety Device
Your heater is fitted with a safety
device that switches off the lower
three quartz heating elements in the
event of overheating. Should this
happens, turn off the heater and
inspect the air inlet and outlet for
blockages. Wait at least five minutes
for the over-heat protection system
to reset before attempting to restart
the heater.
If the heater fails to operate or the
safety device switches off the lower
three quartz heating elements again,
return the heater to your nearest
Kambrook Service Centre
for examination or repair.
Using Your Kambrook Dual Heater
Before First Use
1. Remove your heater from its
carton and associated protective
wrapping, and unwind the cord
to its full length and remove any
protective cardboard or foam
that may have been used to
minimize transportation damage.
2. Read and follow the complete
instructions before plugging the
unit into the 230-240 volt supply.
3. Remove the castors from their
storage position on the base and
following the directions in point
8, fit the castors so that they are
positioned on the outer-most
securing holes on the base of the
heater. The heater must never
be operated without the castors
secured in the correct position.
4. Place the heater on a level
surface in a stable position.
Make certain the heater
element control switch is in the
OFF position.
5. Ensure that wheels are mounted
before use.
6. Inside your box you will find two
(2) sets of caster wheels and four
(4) wing screws. To fit wheels to
heater, please turn heater up side
down on an even surface. Align
the two sets of the caster wheels
to the holes on the bottom of the
heater. Screw in the 4 wing screws
and tighten by hand. Turn the
heater over and use it on a stable
and flat surface.
7. Plug the power cord into a
230-240 volt outlet, the red
indicator light will illuminate when
the power outlet is switched on.
8. Turn the Heat Control dial on the
side of the heater from 0 (Off) to
the desired heat setting.
IMPORTANT: Do not
use the unit without the
wheels fitted
IMPORTANT: Never
operate the heater
without the front grill
securely in position.
Turning Your Heater On
This heater has 4 heat settings.
Ensure the Heat Setting dial is turned
to 0 for the OFF position and Variable
Thermostat dial to ‘MAX’.
Plug the cord into a 230V or 240V
power point and switch on.