Filter
Top Products
Step2:
Mounting this unit onto TK-C215VP series
1. Install TK-C215VP series on
the ceiling
Refer to TK-C215VP series “INSTRUCTIONS” for
the installation method.
2. Mounting this unit onto Space
for Heater of TK-C215VP series
• Mount this unit onto DOME CAMERA as
shown in the right figure.
•
Insert the claw of this unit into Space for
Heater.
Make sure to mount properly.
• After inserting this unit into Space for Heater,
make sure to tighten the fastening screw of
this unit with a + screwdriver.
3. Connecting cable
Connect the cable to the [to HEATER] terminal of
TK-C215VP series.
Step3:
Adjust the field of view and lens of the camera
Switch on the power supply of the camera.
Refer to TK-C215VP series “INSTRUCTIONS” on how to adjust the field of view and lens of the
camera.
After adjusting the field of view and lens of the camera, switch off the power supply of the
camera.
Step4: Install the inner dome
Mount the inner dome to the 3 lugs.
Step5: Inserting the Desiccant supplied
Take out the desiccant from the aluminum
package, insert it into the desiccant insertion
space of the camera unit and fasten using the
lug plate.
Step6: Installing the dome cover
1. Cleaning the dome cover
Before mounting, remove any dust or dirt from
the dome cover.
2. Mounting the dome cover to
the base
Mount the dome cover by aligning the 3 posi-
tion marks on the base with the dome cover.
3. Fastening the dome cover
Fasten by tightening the 3 fastening screws of the dome cover using the wrench supplied.
Step7: Check items after installation
Check the following items after installation.
Is the power supply for TK-C215VP series AC 24 V?
Have you inserted the desiccant that comes with this unit?
Does an image appear normally on the monitor after switching on the power for TK-C215VP
series?
Is the cable of this unit connected to the [to HEATER] terminal of TK-C215VP series?
Has the fastening screw of this unit been tightened properly?
o Dimensions(Unit: mm)
* Design and specifications are subject to change without notice.
Note
Mount the inner dome such that it does
not cover the lens.
When mounting the inner dome, make
sure not to move the position of the lens.
Doing so may cause the preset angle of
view to go out of alignment.
Memo
During reconnection or re-installation
after repair or maintenance, make sure to
replace the desiccant with a new one.
Consult your nearby JVC’s dealer on the
replacement procedures.
Serial number of part to be replaced: Use
a LW40790-001A desiccant.
Note
When mounting is performed on a rainy
day, make sure that rain water does not
enter this unit.
Make sure to use the desiccant supplied.
Failure to do so may cause the camera
lens and dome cover to fog.
If the angle of view is not adjusted imme-
diately after mounting the camera, insert
the desiccant after adjustment is com-
pleted. The desiccant loses its effect if it is
exposed to the air for a prolonged period
of time.
2.
3.
[to HEATER]
terminal
Space for Heater
HEATER fastening
hole
Space for Heater
[to HEATER] terminal
HEATER fas-
tening hole
Fastening Screws
Claw
Cable
Cable
TK-C215VP4 is used in the illustration.
Lug(x 3)
Inner
Dome
TK-C215VP4 is used in the illustration.
Desiccant
Insertion Space
Desiccant
Lug Plate
TK-C215VP4 is used in the illustration.
Memo
Dirt that is not removed from the cover
before mounting may appear on the cam-
era’s image.
Do not apply excessive force to the dome
cover such as stretching it.
Note
When mounting the dome cover, take note
that the desiccant is not caught between
base and dome cover.
Specifications
Power supply / Voltage
AC 24 V ± 10%, 60 Hz/50 Hz
Power consumption
18 W (during AC 24 V)
Heater operation
Surrounding temperature -22 °F to 32°F (
-30f to 0f)(auto on/off)
* By using this unit, the operation guarantee temperature of the camera
becomes -22 °F to 122°F (
-30f to 50f)
Mass 56
Accessories
Instructions ..........................................
Warranty Card .....................................
Service Information Card ....................
Desiccant ............................................
(Service Parts No.LW40790-001A)
1
1
1
1
2
3
Position Alignment Mark (x 3)
Wrench (Supplied)
TK-C215VP4 is used in the illustration.
81
45.5
52
Information for Users on Disposal of Old Equipment
Attention:
Thissymbol is
only valid in the
European Union.
[European Union]
Thissymbol indicates that the electrical and electronic equipment should not be
disposed as generalhousehold waste atits end-of-life. Instead, the product
should behanded over to the applicable collection point for the recycling of
electrical and electronic equipment for proper treatment, recovery and recycling
in accordance with yournational legislation.
By disposing of this product correctly, you will help to conserve natur
alresources
and will help prevent potential negative effects on the environment and human
health which could otherwise becaused byinappropriate waste handling of this
product. For more information about collection point and recycling of this product,
please contact your localmunicipal office, yourhousehold waste disposal service
or the shop where you purchased the product.
Penalties may
be applicable for incorrect disposalofthis waste, in accordance
with national legislation.
(Business users )
If you wishtodisposeofthis product, pleasevisit ourweb page
www.jvc-europe.com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wishtodisposeofthis product, pleasedosoinaccordance with
applicable national legislation or other rules in yourcountry for the treatment of
old electrical and electronic equipment.
© 2006 Victor Company of Japa n, Limited
LST0472-001A