Filter
Top Products
E2010 CCN 15206188
(800) 495-0276 D FAX (800) 892-6276
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
1-1/2” DIAPHRAGM PUMP
OPERATOR’S MANUAL
PM15X-X-X-A02
RELEASED: 1-7-04
REVISED: 5-12-10
(REV. 09)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637389 for air section repair (see page 6).
637375-XX forfluidsection repair(see page 4).NOTE: Thiskitalso con-
tains several air motor seals which will need to be replaced.
637390-X major air valve assembly (see page 7).
PUMP DATA
Models see Model Description Chart for “-XXX”..............
Pump Type Metallic Air Operated DoubleDiaphragm..........
Material see Model Description Chart..............
Weight PM15A
-CSS-XXX-A02 62.40 lbs (28.30 kgs)... ...
PM15R
-CSS-XXX-A02 60.26 lbs (27.33 kgs)...
PM15S
-CSS-XXX-A02 78.40 lbs (35.56 kgs)...
Maximum Air Inlet Pressure 120 p.s.i.g. (8.3 bar).........
Maximum Material Inlet Pressure 10 p.s.i.g. (0.69 bar).....
Maximum Outlet Pressure 120 p.s.i.g. (8.3 bar)..........
Maximum Flow Rate
(flooded inlet) 123 g.p.m. (465.6 l.p.m.)....
Displacement / Cycle @ 100 p.s.i.g. 0.617 gal. (2.34 lit.)...
Maximum Particle Size 1/4” dia. (6.4 mm)............
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM -60_ to 280_ F(-51_ to138_ C)...........
Polypropylene 35_ to 175_ F(2_ to 79_ C)...........
SantopreneR -40_ to 225_ F(-40_ to 107_ C)...........
PTFE 40_ to 225_ F(4_ to 107_ C).................
Dimensional Data see page 8................
Mounting Dimension 9” x11.75” (228.6 mmx 298.5 mm)........
Noise Level @ 70 p.s.i., 60 c.p.m. 85.0 db(A)
{.....
The pumpsound pressure levels published here have beenupdated toan Equivalent
Continuous Sound Level(L
Aeq
) to meetthe intent ofANSI S1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
Figure 1
MODEL DESCRIPTION CHART
PM15 X -C S S -X X X -A02
PM15X - CSS - X X X -A02
637375 - X X
DiaphragmBall
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: Model # PM15S-CSS-SAA-A02
Fluid Section Service Kit # 637375-AA
Seat Material
A - Santoprene
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene
M - Medical Grade Santoprene
T - PTFE / Santoprene
Ball Material
A - Santoprene
T - PTFE
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
S - Stainless Steel
Fluid Connection
C - Tri-clamp
Center Section Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
www.ingersollrandproducts.com