Filter
Top Products
c
Dry
hands
and
plug deep cleaner into
a properly grounded outlet.
Step
on
handle release pedal and lower
handle
to
operating position;
turn
deep
cleaner
ON.
To
release
solution,
press trigger. Slowly
move
deep cleaner forward
and
back-
ward
over area
to
be cleaned.
To
pfck
up
dirty
solution,
release trigger
and
slowly
move
deep cleaner over
area
where
solution
has
just
been
dis-
persed.
Use
both
forward
and
reverse
strokes.
Empty
recovery
tank
when
the
motor
sound
becomes higher pitched and
there
is
a
loss
in
suction (see
“Automatic
shut-off”,
page
7)
When
finished cleaning, follow “After
cleaning” instructions
on
pages
9-10.
Remove
attachment
from
nozzle and
rinse
in
clear
water.
Do not remove
plastic screen or foam from attach-
ment.
The
powered
hand
tool
(Ultra models)
has
rotating brushes
for
extra scrubbing
action
on
small carpet
areas,
carpeted
stairs and
upholstery.
The
stair/upholstery nozzle
has
a
built-in
brush
to help provide
the
scrubbing
action
some
spots may
need
for
removal.
The
car cleaning
tool
(Plus
models) can
be
used
for carpet
and
upholstery
in
vehicles.
How to attach tool
Disconnect deep cleaner from electri-
cal outlet.
Place
handle
in
upright position and
remove
hose
from
rack.
q
,
Connect powered
hand
tool
(A)
or
stair/upholstery
nozzle
or
car
cleaning
tool
(B)
to
end
of
hose
by
sliding it
onto
connector
until
the tab
(C)
locks
it
securely.
Using
your
thumb,
push forward and
up
on
the
latch (D)
to
remove
tool
as
shown.
Follow
the
instructions
on
pages
11-12
for
the
appropriate cleaning
task.
After using tool
1.
Follow
steps
a
and
b
for
“After clean-
ing”
on
page
9.
q
A
2.
Rinse
tool
and
hose
by
filling
sink
with
a
small
amount
of
water.
Turn
deep cleaner
ON
and
pickup the water
with
the
tool.
q
1
3.
Drain
hose
by turning deep
cleaner
ON
and holding
end
of
hose
up
for several seconds.
Do
not
press trigger.
4.
Disconnect deep cleaner
from
electri-
cal outlet.
5.
Drain
solution tube (located inside
hose)
by pointing
end
of
hose
in
sink
and
pressing trigger.
6.
Proceed
with
steps
c,
d,
and
e,
for
“After cleaning”
on
page
9.
Read “Before you begin cleaning”
Instructions on page 9.
Place
handle
in
upright position.
Agitator brushes will not rotate while
handle Is in upright position.
Fill
clean
solution
tank
with
HOOVER
Carpet/Upholstery Detergent according
to
instructions
on
pages
7
and
8.
Attach
tool
to
end
of
hose.
Hose
length
may require that machine
be
placed at
the
top
of
the stairs
to
clean upper half
of
stairway and at bot-
tom
of
stairs
to
clean
lower
half.
To prevent machine from falling, use
extra
cautipn
when cleaning on stairs.
Do not place deep cleaner on stairs.
Do not point tools toward people or
pets. Dry
hands
and
plug deep cleaner
into
a
properly grounded outlet.
Turn
deep cleaner
ON.
q
Pre-spray
the
carpeted stair by
’
’ holding
the
tool
(A)
or(B)
about
one
inch
above the carpet
and
push
it
forward while pressing
the
trigger
(equals
one
wet
stroke).
Position
tool
against
the
riser
and
slightly
press
it
into
carpet
pile.
Press
the
trigger
and
pull
the
tool
slowly
over
the
carpet
(second
wet
stroke).
Release
trigger
at
end
of
stroke.
Continued
+
11