Filter
Top Products
2
USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [5]
2. Adjust the telescopic tube to the desired height by moving the telescopic release
button up and raise or lower the handle to the most comfortable cleaning position.
[6]
3. Carpet and Floor Nozzle** - Select the type of surface to be cleaned by pressing the
pedal** in the nozzle. [7]
Hard Floor – Brushes are lowered to protect the oor.
Carpet – Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the On/Off Button on the cleaner main body. [8]
5. Adjust the suction by moving the suction regulator to the desired level.* [9]
6. Switch off at the end of use by pressing the On/Off Button. Unplug and press the
cord rewind button to wind the power cord back into the cleaner. [10]
7. To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the parking slot on the cleaner main body. [11]
ACCESSORIES AND NOZZLES
All accessories can be tted to the end of the hose handle or to the end of the telescopic tube.
2 in 1 tool – Combines several functions in one. [12]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To ex-
tend the brushes push the button on the body of the tool.
Crevice Tool – For corners and hard to reach areas.
Furniture Nozzle – For soft furniture and fabrics [13]
Parquet Caresse Nozzle* – For parquet oors and other delicate oors. [1U]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep-
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1V]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for
deepcleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal. [1W]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1X]
IMPORTANT: Do not use the grand turbo and mini turbo nozzles on rugs with long
fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle station-
ary while the brush is rotating.
CLEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator in the container empty the dust bin.
IMPORTANT:To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the container by sliding the dust container release button towards the rear
of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Hold the dust container over a bin with one hand and use the other hand press the
Dust Container Door Release Button. [15]
3. Close the Dust Container door and ret to the cleaner main body.
Cleaning the washable lters
The cleaner is tted with a blue lter pack. To maintain optimum cleaning performance
regularly remove the the lters and tap against the side of the bin to release dust. The lters
should be washed after 5 container empties or when the lter has excessive dust level.
IMPORTANT: All bagless cleaners require regular lter cleaning. Failure to clean
your lters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
IMPORTANT: Regularly check and maintain the lters by following the lter main-
tenance instructions , it is also recommended that you purchase new lters after
every 3rd lter wash. This will maintain your cleaners performance.
IMPORTANT: Always ensure the lters are fully dry before use.
To access the pre-motor lter:
1. Release the container by sliding the dust container release button towards the rear
of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Hold the dust container with one hand and with the other hand rotate the bin handle
anti clockwise to release it from the dust container. [16]
3. Remove the blue lter pack located in the dust container handle. [17]
4. Gently tap and wash the lter using warm water. Do not use hot water or detergents.
Remove excess water from the lter and leave to dry fully before re-using. [18]
5. Reassemble to lter pack once fully dry and ret to the cleaner.
IMPORTANT: Do not use the product without the lter pack tted.
To access the exhaust lter:
1. Release the container by sliding the dust container release button towards the rear
of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Unclip the exhaust lter cover from the dust container cradle on the cleaner main
body. [19]
3. Using the tab remove the exhaust lter from the cleaner main body. [20]
4. Gently tap and wash the lter using warm water. Do not use hot water or detergents.
Remove excess water from the lter and leave to dry fully before re-using. [21]
* Certain models only
** May vary depending on model
GB
Curve im uk master.indd 2 3/28/2012 1:49:19 PM