Filter
Top Products
© 2008 Honeywell International Inc. • Honeywell, IntelliSense and DUAL TEC are registered trademarks of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved. Made in China
800-02414 Rev B
LED INDICATORS
DIP SWITCH SETTINGS (SW1)
Factory default settings are shown in grey.
DT7450UK2 DUAL TEC
®
Motion Sensor Product Information
TROUBLESHOOTING
Problem: Red LED is flashing rapidly.
Explanation: The sensor is in one of three conditions:
Microwave supervision failure: The sensor continues operating using
PIR as the only detection method. When detection occurs on the PIR
channel, the alarm relay will latch open until the Microwave fault is
removed.
PIR self-test failure: Alarm relay does not actuate.
Temperature compensation failure: When alarm occurs, the alarm relay
will latch open until the fault is cleared.
Solution: Power down the sensor or enter zone finder mode which will
perform self-test. If the fault does not clear, replace the sensor.
Power Up
Slow
Blink
OFF
OFF
LED
Red
Yellow
Green
Normal
ON
Alarm
ON
Microwave
ON
PIR
Fault
Fast
Blink
OFF
OFF
Zone Finder
OFF
ON
Microwave
ON
PIR
OPERATION MODE
Switch
1
2
OFF
Low Sensitivity
(Pulse Count 2)
LED disabled
ON
High Sensitivity
(Pulse Count 1)
LED enabled
Please contact your local authorised Honeywell
representative for product warranty information.
DETECTION PATTERNS
Top View
Wide Angle Lens
Accessories:
Optional Lens Kit -
Long Range Curtain Lens Kit (P/N DT7000-LRLK)
Mounting Brackets -
SMB-10 Swivel Mount Bracket
(P/N 0-000-110-01)
SMB-10T Swivel Mount Bracket w/Tamper
(P/N 0-000-155-01)
SMB-10C Swivel Mount Ceiling Bracket
(P/N 0-000-111-01)
TS 50131-2-4 Compliant Accessories:
SMB-10T Swivel Mount Bracket w/ Tamper
(P/N 0-000-155-01)
Long Range Curtain Lens Kit (P/N DT7000-LRLK)
Approvals/listings:
CE
PD6662
EN 50131-1 and TS 50131-2-4 Security Grade 2,
Environmental Class II.
Suitable for connection to an EN 60950 Class II
Limited Power Source.
Note: In TS 50131-2-4 compliant installations:
mount the sensor at 2.3 m, select the high
sensitivity setting, and install a cover screw
(included).
To obtain applicable EU compliance Declaration of
Conformities for this product, please refer to our
Website, http://www.security.honeywell.com/hsce/
international/index.html. For any additional
information regarding the compliance of this
product to any EU specific requirements, please
contact:
Quality Assurance Department,
Honeywell Security & Custom Electronics,
Newhouse Industrial Estate
Motherwell,
Lanarkshire ML1 5SB,
Scotland,
United Kingdom.
Tel: +44(0)1698 738200
Email: UK64Sales@Honeywell.com.
PRODUCT SPECIFICATIONS
Range:
15 m x 18 m
Alarm relay:
Energized Form A
30 mA, 24 VDC,
40 Ohms resistance maximum
Tamper switch:
(NC) 30 mA, 24 VDC
Power requirements:
7.5 - 16 VDC
25 mA typical, 30 mA maximum,
12 VDC nominal
Microwave frequencies:
24.200 GHz
PIR white light immunity:
6,500 Lux typical
Fluorescent light filter:
50 Hz
Operating temperature:
-10
o
C to +55
o
C (14
o
F to +131
o
F)
5 - 95% relative humidity (non-condensing)
(Indoor use environment)
Temperature Compensation:
Advanced dual slope.
Self-tests:
Microwave Supervision
PIR Self-Test
Temperature Compensation
PIR fields-of-view:
High Security Lens
22 long range edges
12 intermediate edges
6 lower edges
4 look-down edges
Weight:
174 g;
Packaged Product Approx.: 213 g
Dimensions:
11.9 cm H x 7.1 cm W x 4.2 cm D
Sensitivity:
High (Pulse Count 1) 1 - 2 steps
Low (Pulse Count 2) 3 - 4 steps
Side View
Minimum Detection Pattern
Maximum Detection Pattern