Filter
Top Products
• The electrical cord of this product cannot be replaced. If it sus-
tains damage, you must stop using this product immediately
and return it to the HoMedics Service Center for repair. (See the
warranty section for HoMedics address.)
• Disconnect the appliance from supply mains before putting
hands into water.
Assembly and Instructions for Use
1. Unpack the product. Wipe off dust with a damp cloth.
2. Familiarize yourself with the pump. The pump speed is con-
trolled by the switch located at the front of the pump. The
speed is indicated by a plus (+) and minus (-) sign. To increase
the speed, move the switch slowly to the left in the direction of
the plus sign. You will hear a click as the switch moves to each
speed level. At its highest speed level, the switch will cease to
move any further. To decrease the pump speed, move the
switch to the right toward the minus sign. Similarly, at its lowest
speed, the switch will cease to move any further (Fig 8). NOTE:
It is recommended the pump be set at its highest speed during
assembly and later adjusted to a lower setting if desired. Be
sure to unplug the pump before adjusting the speed setting.
3. Lead the cord through the cord slot on the bottom of the Base
(A). This will ensure that the unit is balanced when placed on a
flat surface. Attach the A/C adaptor jack to the base power
cord. DO NOT plug into outlet at this time. See Figure 1.
4 5
4. Slide the waterproof light into the
socket clip attached at the inner side
of the slate holder (C).
5. Take the tube on the bottom side of
the Top Slate (B) and place it through
the Slate Holder (C). Place this all
the way so that you can see the tube
through the opening on the back of
the Slate Holder (C). See Figure 2.
NOTE: When placing the top slate
(B) onto the slate holder (C) be sure
to line up the top slate notches with
the slate holder cut-outs.
6. Place the Slate Holder (C) with the
Top Slate attached (B) evenly across
the Base (A). Connect the tube to the
pump. See Figures 3 and 4. NOTE:
When placing slate holder (C) onto
Base (A), be sure to line up the open-
ing of slate holder (C) with the
notches on Base (A).
7. Insert the Slate (D) into the “U”
shaped slot (lowest) on the back of
the Slate Holder (C), to cover the
pump. Insert Slates (E, F, G) into the
Slate Holder as illustrated in the dia-
gram. See Figure 5. NOTE: This is
the slate positioning that we recom-
mend. The slates are interchangeable
and will fit into any of the slots on the
Slate Holder. The slates can be
arranged differently - by pulling the
slates in or out - the fountain will pro-
duce different water patterns and
sounds.
8. Arrange the stones provided onto the
base and slates. See Figure 6.
9. Look through the opening on the
back of the slate holder and fill the
entire bottom of the base, up to the
bottom Slate Holder, with clean water.
Water should be visible through the
back opening in the slate holder but
should not be rising above the bot-
tom of the Slate Holder.
10. Plug the cord into 120V household
outlet. The fountain is controlled by
the switch located on the power
cord. If pump doesn’t operate,
rotate in-line switch once to turn
“on” and once more to turn “off”.
Figure 2
C
B
Figure 3
A
B
C
Figure 6
Figure 4
Figure 5
A
B
C
Stones
Switch
Adaptor
Cord Slot
Waterproof light
(A) Base
Slate G
Slate F
Slate E
(D) U-Shaped Slate
Slate Holder
(B) Top Slate
Light Socket Clip
Pump
D
E
F
G
Cut-outs
Notches
Figure 1
Opening
Notches
Opening