Filter
Top Products
• The electrical cord of this product cannot be replaced. If it
sustains damage, you must stop using this product immedi-
ately and return it to the HoMedics Service Center for repair.
(See the warranty section for HoMedics address.)
• Disconnect the appliance from supply mains before
putting hands into water.
Assembly and Instructions for Use
1. Unpack the product. Wipe off dust with a damp cloth.
2. Familiarize yourself with the pump. The pump speed is con-
trolled by the switch located at the front of the pump. The
speed is indicated by a plus (+) and minus (-) sign. To
increase the speed, move the switch slowly downward in
the direction of the plus sign. You will hear a click as the
switch moves to each speed level. At its highest speed level,
the switch will cease to move any further. To decrease the
pump speed, move the switch upward toward the minus
sign. Similarly, at its lowest speed, the switch will cease to
move any further (Fig 9). NOTE: It is recommended the
pump be set at its highest speed during assembly and later
adjusted to a lower setting if desired. Be sure to unplug the
pump before adjusting the speed setting.
3. Lead the cord through the cord slot on the bottom of the
Base (A). This will ensure that the unit is balanced when
placed on a flat surface. Attach the A/C adaptor jack to the
base power cord. DO NOT plug into outlet at this time. See
Figure 1.
4. Slide the waterproof light into the socket clip attached at the
inner side of the slate holder (C).
5. Attach the large end of the tube to the connector located
under the Top Slate (B). See figure 1.
4 5
6. Take the tube on the bottom side
of the Top Slate (B) and place it
through the Slate Holder (C). Place
this all the way so that you can see
the tube through the opening on
the back of the Slate Holder (C).
See Figure 2. NOTE: When placing
the top slate (B) onto the slate
holder (C) be sure to line up the
top slate notches with the slate
holder cut-outs.
7. Place the Slate Holder (C) with the
Top Slate attached (B) evenly
across the Base (A). Connect the
small end of the tube to the pump.
See Figures 3 and 4. NOTE: When
placing slate holder (C) onto Base
(A), be sure to line up the opening
of slate holder (C) with the notches
on Base (A).
8. Insert the Slate (D) into the “U”
shaped slot (lowest) on the back of
the Slate Holder (C), to cover the
pump. Insert Slates (E, F, G) into
the Slate Holder as illustrated in the
diagram. See Figure 5. NOTE: This
is the slate positioning that we rec-
ommend. The slates are inter-
changeable and will fit into any of
the slots on the Slate Holder. The
slates can be arranged differently -
by pulling the slates in or out - the
fountain will produce different water
patterns and sounds.
9. Arrange the stones provided onto
the base and slates. See Figure 6.
10.Look through the opening on the
back of the slate holder and fill the
entire bottom of the base, up to the
bottom Slate Holder, with clean water.
Water should be visible through the
back opening in the slate holder but
should not be rising above the bot-
tom of the Slate Holder.
11.Plug the cord into 120V household
outlet. The fountain is controlled by
the switch located on the power
cord. If pump doesn’t operate, rotate
in-line switch once to turn “on” and
once more to turn “off”. NOTE:
Ensure that the electrical cord loops
below the electrical outlet to form a
‘Drip Loop’ (Fig. 7). This will prevent
water from running down the cord
into the electrical outlet.
Figure 2
C
B
Figure 3
A
B
C
Figure 6
Figure 4
Figure 5
A
B
C
Stones
Switch
Adaptor
Cord Slot
Waterproof light
(A) Base
Slate (G)
Slate (F)
Slate (E)
(D) U-Shaped Slate
Slate Holder
(B) Top Slate
Light Socket Clip (C)
Pump
Tube
D
E
F
G
Cut-outs
Notches
Figure 1
Opening
Notches
Opening
Drip Loop
Figure 7
WFL-ROC_SP.qxd 2/14/06 12:14 PM Page 5