Filter
Top Products
WALL MOUNTING INSTRUCTIONS:
CAUTION: PLEASE MAKE SURE THE HEATER IS UNPLUGGED AND COOLED
DOWN TO ROOM TEMPERATURE BEFORE WALL MOUNTING THIS UNIT.
This unit has the unique feature of using the base as the wall mount
bracket. (Wall mounting hardware is not supplied.) Refer to Figure 2. To
install the heater on the wall, follow these easy steps:
Note: If your unit has casters attached, you’ll need to remove them. If the
base is still attached to the bottom of the heater, you’ll need to remove it
(follow step 5 in assembly instructions).
1. Select a location on the wall where you would like to have the
heater mounted.
2. Use the base as a template for hole locations
3. Use appropriate hardware for different mounting surfaces (see below).
Selected hardware must be able to support a minimum of
twenty-pound weight.
4. When securing the base/wall mount to the wall, keep the lock tab
to your left.
5. Once the base/wall mount is in place, align the mounting tabs on the
back of the heater with the holes in the base/wall mount and slide the
heater to the right until it stops and is secure.
6. To remove the heater, simply slide it to the left.
NOTE: This unit is not to be mounted in ways other than shown in Figure 2.
There are many ways to attach your heater to vertical walls if desired.
Please, use the applicable section of this manual to safely install
your heater.
For wood walls
You’ll need a 1/8" drill bit and two #10-12 x 1 1⁄2" screws
1. Use the base of the heater as a template to outline the hole location
2. Using 1/8" drill bit, drill 1 1⁄4" deep pilot holes
3. Protrude the screws through the two outer holes in the base and secure
the base to the wall
4. Slide the heater onto the base
For drywalls with studs
We recommend that you use wooden studs behind the drywall for better
support and performance of your heater. Remember that in most
American homes, studs behind the wall are spaced 16" apart and the
drywall is 1⁄2"-5/8" thick. Note that the distance between the two farthest
holes of the base is 16" as well.
1. Find studs behind the drywall.
2. Use the base of the heater as a template to center the holes on studs
3. Using 1/8" drill bit, drill 1 3⁄4" deep pilot holes
4. Protrude #10-12 x 2" screws through the two outer holes in the base
and screw them into pre-drilled holes
5. Slide the heater onto the base
For drywalls without studs and other solid walls
1. Use the base of the heater as a template to outline the hole location
2. Using 1⁄4" drill bit, drill pilot holes through the wall
3. Insert 1⁄4" plastic anchors into the holes
4. Protrude #10-12 x 1 1/2'’ screws through the two outer holes in the
base and screw them into the anchors
Slide the heater onto the base
OPERATING INSTRUCTIONS:
1. Unless wall mounted, place heater on a firm level floor surface.
2. For heater operation, please set the Thermostat all the way to HI.
(See Figure 1)
3. Turn the Selector Control to desired heat setting
(LO for 750W or HI for 1500W).
4. The Power Light will remain lit during operation
Note: This unit does not have a fan. It warms the air by natural
convection.
THERMOSTAT INSTRUCTIONS:
1. You need to set thermostat on HI to start heater (See Figure 1).
Allow heater to operate and warm up the room.
2. When the desired temperature/comfort level is reached, lower the
thermostat setting until the heater stops operating.
3. The control will now automatically maintain the pre-set temperature
level by turning the heater ON and OFF. The Temperature Range
Display can be used as guidance, but will not provide exact
measurement.
Note: It is normal for the heater to cycle ON and OFF as it maintains the
preset temperature. To prevent the unit from cycling, you need to raise
the thermostat setting.
Note: The LED Display shows approximate temperature settings.
ILLUSTRATIONS
PLEASE READ AND SAVE THESE
IMPORTANT SAFEGUARDS
When using electrical appliances, basic precautions should
always be taken to reduce the risk of fire, electric shock,
and injury to persons, including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance directly into a
120 V AC electrical outlet.
3) The heater is hot when in use. To avoid burns, DO NOT let bare skin
touch hot surfaces. If provided, use handles when moving this
heater. Keep combustible materials, such as furniture, pillows, bed-
ding, papers, clothes, and curtains at least 3 ft (0.9 m) from the
front of the heater and keep them away from the sides and rear.
4) DO NOT run cord under carpeting. DO NOT cover cord with throw
rugs, runners, or the like. Arrange cord away from traffic area and
where it will not be tripped over.
5) This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. NEVER locate heater where it may fall into
a bathtub or other water container.
6) This unit is wall mountable, but DO NOT mount heater on ceilings.
7) Extreme caution is necessary when any heater is used by, or near
children or invalids, and whenever the heater is left operating
and unattended.
8) Always unplug the heater when not in use.
9) When unplugging, be sure to pull by the plug and not the cord.
10) DO NOT insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
11) DO NOT operate heater with a damaged cord or plug, or after the
heater malfunctions, has been damaged in any manner. Return
appliance to manufacturer for examination, electrical or mechanical
adjustment, or repair.
12) A heater has hot and arcing or sparking parts inside. DO NOT use
it in areas where gasoline, paint, or flammable liquids are used
or stored.
13) Use appliance only for intended household use as described in this
manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons. The use of
attachments not recommended or sold by The Holmes Group may
cause hazards.
14) DO NOT use outdoors.
15) To prevent a possible fire, DO NOT block air intakes or exhaust in
any manner. DO NOT use on soft surfaces, like a bed, where
openings may become blocked.
16) To disconnect heater, turn controls to OFF, then remove plug
from outlet.
17) Avoid the use of an extension cord because the extension cord may
overheat and cause a risk of fire. However, if you have to use an
extension cord, the cord shall be No. 14 AWG minimum size and
rated not less than 1875 watts.
18) If the heater will not operate, see specific instructions on Auto Safety
Shut-off.
19) DO NOT attempt to repair or adjust any electrical or mechanical func-
tions on this unit. Doing so will void your warranty. The inside of
the unit contains no user serviceable parts. All servicing should be
performed by qualified personnel only.
Thank you for choosing a Holmes heater. To ensure the best
performance from your heater, please read and save the
following instructions.
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
AUTO SAFETY SHUT-OFF WITH INSTANT TIP-OVER PROTECTION
:
This heater is equipped with a patented, technologically-advanced safety sys-
tem that requires the user to reset the heater if there is a potential overheat
situation. When a potential overheat temperature is reached, the system
will automatically shut the heater off. It can only resume operation when
the user resets the unit.
To Reset the Heater:
1. Turn the Selector Control to the OFF position and thermostat to HI
2. Unplug the heater and wait 10 minutes for the unit to cool down
3. After the 10 minutes, plug the unit in again and operate normally.
Tip-Over Shut Off:
When the unit is accidentally knocked over, it will instantly shut off. To
reset, simply place the heater in an upright position.
PRE-OPERATING INSTRUCTIONS:
1. Carefully remove your heater from the box. (please save the carton
for off-season storage).
2. Make sure the unit is in the OFF position before plugging the heater
into the outlet.
3. Place heater on firm level surface after attaching base (see below for
assembly)
4. Avoid overloading your circuit by not using other high wattage
appliances in the same outlet. At 1500 Watts, this unit draws
12.5 Amps.
FOR FLOOR OR WALL MOUNT USE ONLY
ASSEMBLY INSTRUCTIONS:
There are 4 casters and 1 base provided within the packaging that you will
need to assemble the heater.
Note: Casters are not necessary for the unit to run properly. If you wish to
install the base without casters skip to step 3.
1. Carefully remove the base and 4 casters from the box.
2. Turn the base upside down and push caster shafts into the 4
corresponding holes on ends of the base.
3. Carefully remove the heater from the box and turn it upside down
with grill facing you. The control panel will be on your left.
4. Place the base (with the tab on the left) on what now is the top of the
heater directly onto the corresponding locators and slide the base to
the left. This will secure the unit and the base together.
5. To remove the heater from the base, turn the heater upside down
(with the grill facing you), and slide the base to the right and lift it up.
Page2 Page 3
FIGURE 1
FIGURE 2
SELECTOR CONTROL
0 = OFF
II = HI (1500 Watts)
I = LO (750 Watts)
THERMOSTAT