Holmes HT30 Fan User Manual


 
OPERATING INSTRUCTIONS
IMPORTANT:
Step 1: Set the fan base on a dry, level surface.
Step 2: Plug the cord into any standard 120-volt A/C outlet.
To turn the fan on press one of the three speed buttons
marked (1) low, (2) medium, or (3) high. To turn the fan off
press the button marked (0) off.
Step 3: The SPEED is adjusted by pressing one of the three buttons
for your desired level of cooling comfort.
Step 4: The OSCILLATION button is located on the top of the fan
control panel. To start oscillation, push button down. To stop
oscillation, push the button again.
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for your
Holmes Tower Fan. Please remember:
Always unplug the fan before cleaning or disassembling.
Do not allow water to drip on or into the fan motor housing.
Do not use any of the following as a cleaner: gasoline,
thinner, benzine.
We also recommend the periodic cleaning of this fan by lightly
running a vacuum cleaner nozzle over the fan grill to remove
any dust or dirt that may have accumulated inside or on the unit.
Fan Head and Base Cleaning
Using a soft, moist cloth, with or without a mild soap solution,
carefully clean the fan housing. Please use caution around
the grills. Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
Your fan can be stored in the off-season either partially disassembled
or assembled. It is important to keep it in a safe, dry location.
If stored disassembled, we recommend using the original
(or appropriately sized) box.
If stored assembled or partially assembled, remember to protect
the fan head from dust.
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and injury
to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance directly into
a 120 V AC electrical outlet.
3. Keep the cord out of heavy traffic areas. DO NOT let the cord
hang over the edge of a table or counter. To avoid fire hazard,
NEVER put the cord under rugs, near heat registers, radiator,
stoves, or heaters.
4. To protect against electrical hazards, DO NOT immerse in water or
other liquids. Do not use near water.
5. Close supervision is necessary when any appliance is used by or
near children, or by disabled people.
6. Always unplug the fan before moving it, putting on or taking off
parts, cleaning, or whenever the fan is not in use. Be sure to pull
by the plug and not the cord.
7. Avoid contact with moving parts. DO NOT operate without fan
grills properly in place.
8. DO NOT operate any appliance with a damaged cord or plug, if
motor fan fails to rotate, after the appliance malfunctions, or if it
has been dropped or damaged in any manner. Return appliance to
manufacturer for examination, electrical or mechanical adjustment,
or repair.
9. DO NOT operate in the presence of explosive and/or flammable
fumes.
10.Use appliance only for intended household use as described in this
manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons. The use of
attachments not recommended or sold by Holmes may cause
hazards.
11.DO NOT use outdoors.
12.Always use on a dry, level surface.
13.Keep unit away from heated surfaces and open flames.
14.WARNING: To reduce the risk of fire or electric shock, DO NOT use
this fan with any solid-state speed control device.
15.DO NOT attempt to repair or adjust any electrical or mechanical
functions on this unit. Doing so will void your warranty. The inside
of the unit contains no user serviceable parts. All servicing should
be performed by qualified personnel only.
ASSEMBLY INSTRUCTIONS
Step 1: Remove all contents from the box being careful not to
discard the manual and hardware needed for assembly.
Step 2: Pass the power cord through the channel of the stand,
and firmly clasp the two halves of the stand together.
Insert the base into the bottom of the housing being careful
to align the corresponding holes.
Step 3: Gently turn the fan upside down, with the top of the fan
touching the floor. Screw the stand into the bottom portion of
the fan housing, by using the 2 thumb screws that come with
the fan.
Step 4: Place the power cord through the cut out on the bottom of
the base. To reduce movement of the power cord during use
or transportation, turn the cord clip appoximately 90 degrees
to the right until the clip covers the power cord.
Step 5: Place the fan right side up and it is ready for use.
ILLUSTRATIONS
HT30 fan 9/01
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current)PLUG (a plug having one blade wider
than the other). This plug will fit into the power outlet only
one way. If the plug does not fit fully into the outlet, reverse
the plug. If it still does not fit, contact qualified personnel to
install the proper outlet. DO NOT DEFEAT THE SAFETY
PURPOSE OF THIS POLARIZED PLUG IN ANY WAY.
PLEASE READ AND SAVE THESE IMPORTANT
SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
FIGURE 3
FIGURE 4
FIGURE 1
A.THUMB SCREW
(FIGURE 1)
B.CORD CLIP
(FIGURE 2)
C. DUST FLAP
(FIGURE 3)
D.OSCILLATION BUTTON
(FIGURE 3)
E. SPEED CONTROL
BUTTONS (FIGURE 4)
F. FAN HOUSING
(FIGURE 4)
G.FRONT GRILL
(FIGURE 4)
H.BASE
(FIGURE 4)
A
B
C
D
E
F
G
H
FIGURE 2