Filter
Top Products
P L E A S E R E A D A N D S A V E T H E S E
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
F E A T U R E S - O P E R A T I O N S
3. Set the airflow direction by sliding the fan directional
switches located above each fan blade. Note that the
fan blades work independently from one another and
can be used for air intake (bring fresh air in from
outside), exhaust (push air out from within the room)
or exchange (cycles air in and out of the room
simultaneously).
Auto Mode
Your fan is equipped with the AccuTemp Plus™ Digital
Thermostat that will automatically turn the fan ON and
OFF depending upon the preset comfort temperature. This
is ideal for nighttime operation when temperatures can
drop below comfort levels.
Setting Auto Mode
1. Press the Mode button (D) to scroll to the desired
auto speed setting (A3, A2, or A1).
2. Choose the desired temperature setting by pressing
the Temp Up (+) or Temp Down (-) buttons. You may
select a temperature between 60 and 80 degrees
Fahrenheit. Once the desired temperature is set, the
digital display will return to show the ambient room
temperature. View the set temperature by pressing
either the Temp Up (+) or Temp Down (-) buttons.
For example, if you set your thermostat to 75
degrees then your fan will run until the set
temperature is reached. Once the temperature rises
above the set temperature the fan will automatically
turn on again.
IMPORTANT: If the fan does not start in the Auto mode,
please be sure that the set temperature is below the
current room temperature. Lower the set temperature if
you would like for the fan to start or switch over to the
manual speed modes.
Setting the Timer
1. Hold both the Temp Up (+) and Temp Down (-)
buttons down until the digital display flashes “00”.
2. Press the (+) or (-) buttons to change time in 1 hour
increments. Note selection ranges from 1 to 16
hours. When in the timer mode, the time remaining
will be displayed.
NOTE:
• The Timer Light will glow indicating the timer function
is active.
• If Timer is set when fan is ON, the time displayed will
turn the fan OFF once elapsed. If Timer is set when
fan is OFF, the time displayed will turn the fan ON.
(The default ON speed setting is Manual Low)
• Timer function can be turned off by pressing the
MODE key at any time.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan. Please remember:
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
order a new fuse at 1-800-546-5637. Follow the below
instructions to replace the fuse on the plug.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
NOTE: Ensure that fuse
cover is completely open
before attempting to
remove fuse.
3. Remove fuse carefully by
using a small screwdriver
to pry the fuse out of the
compartment by the metal
ends of the fuse. (see
Figure 2)
4. Place plug on a solid, flat surface. Insert new 5 Amp,
125 Volt fuse into fuse compartment and use a small
screwdriver to secure the metal ends of the fuse into
the compartment.
CAUTION: Risk of fire. Replace fuse only with 5
Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the fuse.
INSTALLATION INSTRUCTIONS
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
The window fan comes fully assembled and is ready for
immediate installation.
This window fan has been designed to fit double-hung
windows with minimum openings of 24 inches (60 cm)
wide and 12 inches (30 cm) high.
NOTE: THIS FAN IS DESIGNED AND RECOMMENDED FOR
USE WITH A SCREEN IN THE WINDOW.
Window Fan Installation
1. Align the Window Fan horizontally in the window with
the controls facing you and the Built-In Extender
Panel (J) to the right.
2. Set the fan into your window opening.
3. If the fan does not fit snugly to the left and right of
the window casing, pull out the Built-In Extender
Panel (J) until the fan sits safely in your window.
4. If the fan still does not fit snugly attach the Slider
Safe
®
Extender Panel located in the polyfoam
packaging in the original box. Align the slot in the
Slider Safe
®
Extender Panel along the tab located on
the left side of your Window Fan. Slide the Slider Safe
®
Extender Panel completely down the tab until it is flush
on both the top and bottom of the Window Fan.
5. To keep the fan in place, carefully close the window
so that the bottom edge of the window rests on the
flat area on the top of the fan.
For Slider Windows
1. Set the Fan Vertically in your window opening with
the left side of the fan situated on the bottom and
the Built-In-Extender panel on top.
2. Set the fan into your window opening (note that in
most cases the window screen does not have to be
removed or left open).
3. If the fan does not fit snugly to the top and bottom
of the window casing, attach the Slider Safe
®
Extender Panel and adjust the built-in extender
screen until the fan fits securely in your window.
WARNING: BE SURE FAN IS SECURELY INSTALLED IN
YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON
THE FAN WHILE IT IS IN THE WINDOW.
OPERATING INSTRUCTIONS
1. Plug cord into any standard 120 volt AC outlet.
2. To turn the fan on and control the speed, press the
Mode Button (D). Note that pressing the mode button
will allow you to cycle through the speed setting
(High = 3, Med = 2, Low = 1) as well as the
Automatic Thermostat Temperature settings (Auto
High = A3, Auto Medium = A2, Auto Low = A1). 0
indicates the Off position.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug the
appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all
parts properly in place.
17. This product is intended for household use ONLY and
not for commercial or industrial applications.
18. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
19. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse
blows, a short circuit may be present and the product
should be discarded or returned to an authorized
service facility for examination and/or repair.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
F E A T U R E S - O P E R A T I O N S
C L E A N I N G / M A I N T E N A N C E
A. Front Grill
B. Left Fan Directional Switch
C. Control Panel
D. Mode Button
E. LED Display
F. Temp Up (+)
G. Temp Down (-)
H. Right Fan Directional Switch
I. Extender Locks
J. Built-In Extender Panel
A
B
C
D
E
F
G
H
I
I
J
Figure 1
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
Figure 2
Fuse
Metal ends
Fuse cover
HAWF3095_11EM1.indd 2 7/15/11 9:59 AM