Filter
Top Products
FEATURES - OPERATIONS
Step 3: Place the base nut on the threaded section and hand-tighten the
base nut to securely fasten the lower extension pole to the base.
Step 4: Insert the other pole with the threaded joint (male end) into the
hollow end of the lower pole (female end), until both poles
meet. Be careful to align the cutaway / grooves on the
threaded joint (male end) with the two protruding pieces inside
the hollow end of the lower pole (female end).
Step 5: Turn the upper pole clockwise to lock it securely in place.
Final Assembly
Step 1: Insert the neck of the fan head into the hollow end of the pole
and turn the neck clockwise to lock into place.
OPERATING INSTRUCTIONS
Step 1: Set the fan base on a dry, level surface.
Step 2: Please make sure the On/Speed knob is in the "Off" or "0"
position. Plug the cord into any standard 120-volt A/C outlet.
Step 3: The SPEED is adjusted by moving the knob left or right to the
desired setting.
Step 4: The OSCILLATION control knob is located on the top of the fan
motor housing. To start oscillation, push control knob down. To
stop oscillation, pull control knob up.
ADJUSTMENT INSTRUCTIONS
Height Adjustment
This fan is equipped with two poles, which allow you to adjust the height
of the fan for three height settings.
Tilt Adjustment
To change the tilting angle of the fan head, move the fan head to
the desired angle.
CLEANING/MAINTENANCE
Follow these instructions to correctly and safely care for your Holmes
Power Stand Fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline,
thinner, benzine.
• We also recommend the periodic cleaning of this fan by lightly
running a vacuum cleaner nozzle over the fan grill to remove any
dust or dirt that may have accumulated inside or on the unit
FAN STORAGE
Your fan can be stored in the off-season either partially disassembled
or assembled. It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using the original
(or appropriately sized) box.
• If stored assembled or partially assembled, remember to protect
the fan head from dust.
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance directly into a
120 V AC electrical outlet.
3) Keep the cord out of heavy traffic areas. DO NOT let the cord
hang over the edge of a table or counter. To avoid fire hazard,
NEVER put the cord under rugs, near heat registers, radiator,
stoves, or heaters.
4) To protect against electrical hazards, DO NOT immerse in water or
other liquids. Do not use near water.
5) Close supervision is necessary when any appliance is used by or
near children, or by disabled people.
6) Always unplug the fan before moving it, putting on or taking off
parts, cleaning, or whenever the fan is not is use. Be sure to pull
by the plug and not the cord.
7) Avoid contact with moving parts. DO NOT operate without fan
grills properly in place.
8) DO NOT operate any appliance with a damaged cord or plug, if
motor fan fails to rotate, after the appliance malfunctions, or if it
has been dropped or damaged in any manner. Return appliance
to manufacturer for examination, electrical or mechanical adjust-
ment, or repair.
9) DO NOT operate in the presence of explosive and/or
flammable fumes.
10) Use appliance only for intended household use as described in this
manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons. The use of
attachments not recommended or sold by The Holmes Group may
cause hazards.
11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open flames.
14) WARNING: To reduce the risk of fire or electric shock, DO NOT use
this fan with any solid-state speed control device.
15) DO NOT attempt to repair or adjust any electrical or mechanical
functions on this unit. Doing so will void your warranty. The
inside of the unit contains no user serviceable parts. All servicing
should be performed by qualified personnel only.
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current) PLUG (a plug having one blade wider
than the other). This plug will fit into the power outlet
only one way. If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact qualified
personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
ASSEMBLY INSTRUCTIONS
Base / Pole Assembly
NOTE: Poles are the same size and are interchangeable
Step 1: Insert one of the poles through the base cover and twist the
pole clockwise to lock in position. Be careful to align the
cut-away grooves on the threaded joint (male end) with the two
protruding raised pieces inside the hollow end of the base cover.
Step 2: Turn the base cover upside down (with the top of the pole you
just inserted facing the floor) and place the weighted insert into
the base cover. The pole threads will be exposed as they
protrude through the insert.
NOTE: HOLD THE POLE, BASE COVER AND WEIGHTED INSERT IN ONE
HAND WHILE TIGHTENING THE BASE NUT WITH THE OTHER HAND.
I
E
F
G
H
A. Front grill
B. Rear grill
C. Speed control knobs (not shown)
D. Oscillation control knob
E. Pole (interchangable)
F. Pole (interchangable)
G. Base
H. Weight
I. Base nut
B
D
Figure 1
C
A
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS