Holmes HASF2120RC Fan User Manual


 
ASSEMBLY INSTRUCTIONS:
Base Assembly:
You will need the base and four extension legs.
Push in the small tab on each extension and snap into base.
Pole Assembly:
STEP 1: Remove the
base collar from the
base
by turning counter-
clockwise.
STEP 2: Take the
extension pole, with
the solid end down,
and insert it into the
base. The hollow end
of the pole (with the
screw hole) will be
facing up.
STEP 3: Replace the
base collar over the
extension pole, slide
it down the pole, and
secure it to the base by turning clockwise.
Fan Head Assembly:
You are now ready to assemble the fan head
(See Figure #1)
Step 1: Position the rear grill over the motor shaft,
making certain the 2 notches at the top and
bottom of the rear grill fit over the 2 prongs on
the motor housing. Please make sure the rear
grill fits securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear
grill mounting nut. Turn this nut clockwise and
tighten firmly.
Step 3: Slide the fan blade, with the hollowed interior of
the blade facing towards the rear grill firmly onto
the motor shaft. Make sure the shaft protrudes
from the front of the blade.
A. LOGO PLATE (SNAP ON)
B. FRONT GRILL
C. BLADE CAP
D. FAN BLADE
E. REAR GRILL
MOUNTING RING
F. PLASTIC BAND
G. GRILL SCREW
H. REAR GRILL
I. MOTOR SHAFT
J. GRILL MOUNT
K. MOTOR HOUSING
L. TILT JOINT
M. FAN POST SCREW
N. REMOTE CONTROL HOUSING
O. EXTENSION POLE
P. BASE COLLAR
Q. BASE
R. FOOT EXTENSIONS (4)
A
L
B
C
D
E
F
G
H
I
K
J
Figure 1 (HASF2120RC shown)
M
N
O
P
Q
R
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, elec-
tric shock, and injury to persons, including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance
directly into a 120 V AC electrical outlet.
3) Keep the cord out of heavy traffic areas. DO NOT let
the cord hang over the edge of a table or counter.
To avoid fire hazard, NEVER put the cord under rugs,
near heat registers, radiator, stoves, or heaters.
4) To protect against electrical hazards, DO NOT
immerse in water or other liquids. Do not use
near water.
5) Close supervision is necessary when any appliance
is used by or near children, or by disabled people.
6) Always unplug the fan before moving it, putting on
or taking off parts, cleaning, or whenever the fan
is not in use. Be sure to pull by the plug and not
the cord.
7) Avoid contact with moving parts. DO NOT
operate without fan grills properly in place.
8) DO NOT operate any appliance with a damaged
cord or plug, if motor fan fails to rotate, after the
appliance malfunctions, or if it has been dropped
or damaged in any manner. Return appliance to
manufacturer for examination, electrical or
mechanical adjustment, or repair.
9) DO NOT operate in the presence of explosive and/
or flammable fumes.
10) Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by The
Holmes Group may cause hazards.
11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open
flames.
14) WARNING: To reduce the risk of fire or electric shock,
DO NOT use this fan with any solid-state speed
control device.
15) DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no
user serviceable parts. All servicing should be
performed by qualified personnel only.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
Step 4: Secure fan blade onto the motor shaft by turning
the blade cap in a counter-clockwise direction until
it is firmly in place.
Step 5: Prepare the front grill by simply snapping the
circular front grill logo plate in place.
Step 6: Center the front grill by aligning the Holmes logo
so it is horizontal and parallel to the floor. Then
secure the front and rear grills completely
together by snapping into place. Lastly, tighten
the grill screw at the bottom of the rear grill.
Remote Control Handheld Unit:
Your remote control requires 2 AAA
batteries for operation. To install the
batteries, simply depress the back of the
remote with your thumb on the spot marked
OPEN. Insert batteries according to the dia-
gram shown inside. Replace cover.
Figure 4 •Do not mix old and new batteries.
•Do not mix alkaline, standard
(carbon-zine), or rechargeable
(nickel-cadmium) batteries.
Final Assembly:
First, place fan head assembly onto the extension
pole, lining up the fan post screw with the hole in the
extension pole. Then, simply insert the fan post screw
into the hole and tighten until a secure fit is obtained.
Lastly, insert the tilt adjustment knob into the neck
joint and tighten
in place.
NOTE: If your fan
does not have a
screw hole in the
extension pole
but instead has an indentation around the top of the pole;
please do the following:
Step 1: First, place the fan head assembly onto the
extension pole and tighten the fan post screw
until a secure fit is obtained.
Step 2: Insert the tilt adjustment knob into the neck joint
and tighten in place.
OPERATING INSTRUCTIONS:
STEP 1: Set fan on a dry, level surface.
STEP 2: Plug cord into any standard 120V AC outlet.
STEP 3: The speed is adjustable by pushing either the
On/Spd button on the remote control, or the
On/Speed
button on the touch-key pad. Push this button first
for LOW, again for MEDIUM, and a third time for
HIGH. Push a fourth time to repeat the sequence.
To turn the fan OFF, push the OFF button on the
remote control, or on the touch-key pad.
STEP 4: To oscillate the fan head, push the button marked
OSC on the remote, or OSCILLATION on the touch-
key pad. Push a second time to stop OSCILLA-
TION.
STEP5: For a natural breeze movement, push the button
marked Mode, or Mode on the touch-key pad. This
will vary the fan speeds faster and slower. By
pressing the Mode button a second time, or the
SLEEP button on the touch-key pad, you activate
the SLEEP setting. This function slows the fan
speed down, and when used in conjunction with the
timer settings, will ultimately turn the fan off.
NOTE: Both the BREEZE and SLEEP functions can be used
with or without OSCILLATION, and start off of any initial
fan speed.
Fan Post Screw
Extension Pole
Screw Hole
Figure 5
Base
Collar
Extension
Pole
Base
Figure 2
Figure 3
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current) PLUG (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not fit, contact
qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
12/13 HASF2120RC 12.13.2001 04.22pm Page 2