Filter
Top Products
Final Assembly:
First, place fan head
assembly onto the exten-
sion pole, lining up the
fan post screw with the
hole in the extension
pole. Then, simply insert
the fan post screw into
the hole and tighten until
a secure fit is obtained.
NOTE: If your fan does not have a screw hole in the extension pole but
instead has an indentation around the top of the pole; please do the following:
Place the fan head assembly onto the extension pole and tighten the fan
post screw until a secure fit is obtained.
OPERATING INSTRUCTIONS:
Step 1. Set fan base on a dry, level surface.
Step 2. Plug cord into any standard 120 volt AC outlet. Please make sure
the Speed Control Switch is in the Off position. This switch is
located on the top of the Fan Motor Housing.
Step 3. The speed is adjusted by turning the control switch to the desired
setting, Off—High—Med—Low.
Step 4. The Oscillation Control Knob is located on the top of the Fan Motor
Housing. To Start Oscillation, Push Knob Down. To Stop Oscillation,
Pull Knob Up.
ADJUSTMENT INSTRUCTIONS:
Tilt Adjustment:
Follow these instructions to tilt the Fan Head for upward angle air movement.
Step 1: To change the tilting angle of the fan head, simply loosen the Tilt
Adjustment Knob (see figure 3 on Page 2)
Step 2: Move the fan head to the desired angle, then firmly tighten the
knob to lock in place.
Height Adjustment:
Follow these instructions to adjust the height of the fan.
Step 1: Turn the Base Collar (see figure 4) counter-clockwise to loosen
pole.
Step 2: Adjust the pole to the desired height, and firmly tighten the Base
Collar in a clockwise direction.
CLEANING/MAINTENANCE INSTRUCTIONS:
Follow these instructions to correctly and safely care for your Holmes
Products stand fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or enter into the fan housing.
• Be sure to use a soft cloth moistened with a mild soap solution.
• Do not use any of the following as a cleaner: gasoline, thinner, or benzine.
Fan Blade Cleaning:
(See instructions for fan head assembly on page 2, figure 3)
STEP 1: To access the fan blade, remove the front grill and blade cap.
STEP 2: Clean the fan blade, front and rear grills with a soft, moist cloth.
STEP 3: Replace blade, tighten blade cap, and securely fasten the front grill.
Fan Head, Base, and Pole Cleaning:
Using a soft, moist cloth, with or without a mild, soap solution, carefully
clean the fan base, pole, and head. Please use caution around the motor
housing area. Do not allow the motor or other electrical components to be
exposed to water.
FAN STORAGE:
Your fan can be stored in the off-season either partially disassembled or
assembled. It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using the original (or appropri-
ately sized) box.
• If stored assembled or partially assembled, remember to protect the
fan head from dust.
The exclusive Holmes Products FanBonnet is available to protect your fan.
(See attached mail order form for special offer or call 1-800-5-HOLMES)
ASSEMBLY INSTRUCTIONS:
Carefully unpack contents of carton.You will need the base and four
extension legs.
Push in the small tab on each extension and snap into base
Pole Assembly:
You will need the completed base and extension pole.
STEP 1: Remove the base collar from the base by turning counter-clockwise.
STEP 2: Take the extension pole, with the solid end down, and insert it into
the base. The hollow end of the pole (with the screw hole) will be
facing up.
STEP 3: Replace the base collar over the extension pole, slide it down the
pole, and secure it to
the base by turning
clockwise.
Fan Head Assembly:
You are now ready to assemble the fan head (See Figure #3)
STEP 1. Position the rear grill over the motor shaft, making certain the 2
notches at the top and bottom of the rear grill fit over the 2 prongs
on the motor housing. Please make sure the rear grill fits securely
against the motor housing.
STEP 2. Fasten the rear grill in place using the rear grill mounting nut. Turn
the nut clockwise and tighten firmly.
STEP 3. Slide the fan blade, with the hollowed interior of the blade facing
towards the rear grill firmly onto the motor shaft. Make sure the
motor shaft pin lines up with the recessed groove in the back of the
fan blade. Also, be sure the shaft protrudes from the front of the
blade.
STEP 4. Secure fan blade onto the
motor shaft by turning the
blade cap counter-clockwise
(make sure the blade is
firmly in position.)
STEP 5. Center the front grill, align-
ing the Holmes logo so it is
horizontal and parallel to
the floor, place onto the
rear grill, and snap in
place. Secure by tightening
the grill screw at the bot-
tom of the rear grill.
DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM
Tilt Adjustment
Knob
Fan Post Screw
B
D
E
F
C
H
I
G
A
Fan Post
Screw
Base Collar
Bottom
Screw
Figure 3
Figure 4
Fill out form on reverse side or call
1-800-5-HOLMES
to place your order today.
EXTEND THE LIFE OF
YOUR FAN
For short term or seasonal
storage of your Holmes fan
FAN
BONNET
$10.99
PLUS SHIPPING
AND HANDLING
Page2
H
A) Rear Grill
B) Motor Shaft
C) Rear Grill Notches
D) Motor Housing Prongs
E) Mounting Nut
F) Fan Blade
G) Motor Shaft Pin
H) Fan Blade Cap
I) Front Grill
J) Logo Plate
k) Bottom Screw
J
K
Page 3
Base
Collar
Extension
Pole
Base
Figure 1
Figure 2
Fan Post Screw
Extension Pole
Screw Hole
Figure 6