Filter
Top Products
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
FEATURES - OPERATIONS
CLEANING/MAINTENANCE
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner.
10. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
11. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
12. Do not use outdoors.
13. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
14. Always use on a dry, level surface.
15. Do not operate fan until fully assembled with all
parts properly in place.
16. This product is intended for household use ONLY and
not for commercial or industrial applications.
17. WARNING: To reduce the risk of electrical shock
and injury to persons, do not use in window.
18. WARNING: To reduce the risk of fire or electric
shock, DO NOT use this fan with any solid-state speed
control device.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
STEP 6: Center the front grill by aligning the Holmes
®
logo so it is horizontal and parallel to the floor.
Then secure the front and rear grills completely
together by snapping into place. Lastly, tighten
the securing screw at the bottom of the rear grill.
Final Assembly
STEP 1: First, place the fan head assembly onto the
extension pole and tighten the fan post screw
until a secure fit is obtained.
STEP 2: Insert the tilt adjustment knob into the neck
joint and tighten in place.
OPERATING INSTRUCTIONS
1. Set fan on a dry, level surface.
2. Please make sure the Speed Control Knob is in the
OFF position. The Speed Control Knob is located on
the top of the Fan Motor Housing.
3. Plug cord into any standard 120 volt AC outlet.
4. The SPEED is adjusted by turning the control knob to
the desired setting, O(0ff)-III(High)-II(Med)-I(Low).
5. The OSCILLATION Control knob is located on the
top of the Fan Motor Housing. To Start Oscillation,
Push Control Knob down. To Stop Oscillation, Pull
Control knob up.
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment
Follow these instructions to tilt the Fan Head for upward
angle air movement.
STEP 1: To change the tilting angle of the fan head;
simply loosen the Tilt Adjustment Knob.
STEP 2: Move the fan head to the desired angle, and
firmly tighten the knob to lock in place.
Height Adjustment
Follow these instructions to adjust the height of the fan.
STEP 1: Turn the height adjustment knob counter-
clockwise to loosen the extension pole.
STEP 2: Adjust the extension pole to the desired height,
and firmly tighten the base collar in a clockwise
direction.
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for
your stand fan. Please remember:
• Always unplug the fan before cleaning or
disassembling.
• Do not allow water to drip on or into the fan motor
housing.
• Be sure to use a soft cloth moistened with mild a
soap solution.
• Do not use any of the following as a cleaner:
gasoline, thinner, or benzene.
Fan Blade Cleaning
(See instructions for fan head assembly on figure 4)
STEP 1: To access the fan blade, remove the front grill
and the blade cap.
STEP 2: Clean the fan blade, front and rear grills with
a soft, moist cloth.
STEP 3: Replace blade, tighten the blade nut, and securely
fasten the front grill.
Fan Head, Base, and Pole Cleaning
Using a soft, moist cloth, with or without a mild, soap
solution, carefully clean the fan base, pole, and head.
Please use caution around the motor housing area. Do
not allow the motor or other electrical components to be
exposed to water.
FAN STORAGE INSTRUCTIONS
Your fan can be stored in the off-season either partially
disassembled or assembled. It is important to keep it in a
safe, dry location.
• If stored disassembled, we recommend using the
original (or appropriately sized) box.
• If stored assembled or partially assembled,
remember to protect the fan head from dust.
This product is for use on 120 volts. The cord has a plug (A) as shown. An
adapter (C) is available for connecting three-blade grounding-type plugs to two-
slot receptacles (B). The green grounding lug extending from the adapter must
be connected to a permanent ground such as a properly grounded outlet box.
The adapter should not be used if a three-slot grounded receptacle is available.
CAUTION: Use Only with GFCI Protected Receptacles.
ASSEMBLY INSTRUCTIONS
Base Assembly (Refer to Figure 1)
You will need the base and extension legs.
Push in the small tab located on the bottom of each
extension leg and snap into base.
Pole Assembly (See Figure 2 & 3)
STEP 1: Remove the height adjustment knob from the
base by turning counter-clockwise.
STEP 2: Take the pole assembly, with the solid end
down, and insert it into the base. The hollow
end of the pole will be facing up.
STEP 3: Replace the height adjustment knob over the
pole assembly, slide it down the pole, and
secure it to the base by turning clockwise.
Fan Head Assembly
STEP 1: Position the rear grill over the motor shaft,
making certain the 2 notches at the top and
bottom of the rear grill fit over the 2 prongs on
the motor housing. Please make sure the rear
grill fits securely against the motor housing.
STEP 2: Secure the rear grill in its place using the rear
grill mounting-ring. Turn this ring clockwise and
tighten firmly.
STEP 3: Slide the fan blade; with the hollowed interior
of the blade facing towards the rear grill firmly
onto the motor shaft. Make sure the shaft
protrudes from the front of the blade.
STEP 4: Secure the fan blade onto the motor shaft by
turning the fan blade cap in a counter-clockwise
direction until it is firmly in place.
STEP 5: Prepare the front grill by simply snapping the
circular front grill logo plate in place.
Figure 1
Figure 2
Figure 3
A. Logo Plate
B. Front Grill
C. Blade Cap
D. Fan Blade
E. Rear Grill Mounting Nut
F. Plastic Band
G. Rear Grill
H. Grill Screw
I. Motor Shaft With
Support Pin
J. Grill Mount
K. Speed Control Knob
L. Oscillation Knob
M. Motor Housing
N. Tilt Joint
T
S
R
U
Figure 4
O. Tilt Adjustment Knob
P. Fan Post
Q. Fan Post Screw
R. Upper Pole
S. Height Adjustment Knob
T. Lower Pole
U. Extension Legs (4)
A
BC
D
E
F
G
I
K
L
J
M
N
O
P
Q
H
If you have any questions regarding your product or
would like to learn more about other Holmes
®
products, please contact our Consumer Service
Department at 1-800-546-5637 or visit our website
at www.holmesproducts.com
HASF192007EM1.qxd 11/19/07 17:28 Page 2