Filter
Top Products
Final Assembly
Step 1: Insert the neck of the fan head into the hollow end of the pole
and turn the neck clockwise to lock into place.
Step 2: Attach the front of the 1 Touch™ control module by sliding the 2
tabs into the corresponding holes on the pole.
Step 3: Attach the rear of the 1 Touch™ control module to the front by
inserting the 4 clips into the corresponding holes.
Step 4: For additional security, insert and tighten the thumbscrew into
the top rear of the 1 Touch™ control module.
OPERATING INSTRUCTIONS
Your fan is equipped with the technologically advanced 1Touch
™
thermostat. You can set the fan from either the main housing or the
remote control to run continuously in manual mode ore set the 1Touch
™
thermostat to your desired temperature setting. The 1Touch
™
thermostat
will automatically turn the fan ON or OFF depending on the preset
comfort level. The comfort level ranges between 60° and 80° Fahrenheit.
• Set the fan base on a dry, level surface.
• Plug the fan into a 120V AC electrical outlet
•To start the unit and run continuously, push the button on the fan
housing or on the remote control once for the High setting and press
either button twice for the Low setting
•To stop the unit, press and hold the button on the fan housing or on
the remote control for two seconds or keep pressing the button until
all the speed and temperature indicators are OFF
•The OSCILLATION control knob is located on the top of the fan motor
housing. To start oscillation, push knob down. To stop oscillation, pull
knob up
1 Touch
™
Thermostat Instructions
To take advantage of the 1Touch
™
Thermostat, continue to press the button
until the desired temperature is reached. When ambient temperature drops
below the set temperature, the fan will stop. When the room temperature
rises above the set point, the fan will turn on automatically.
Note: It is normal for the fan to cycle ON and OFF as it maintains the
preset temperature. To prevent the unit from cycling, you need to
raise the thermostat setting.
1Touch
™
has memory. The 1Touch
™
thermostat will remember the previous
temperature setting after the unit has been turned off. However if the unit
is unplugged, the 1Touch
™
thermostat will be reset and will no longer
remember the previous temperature setting.
Remote Control Handheld Unit
Your remote control requires 2 AAA batteries for
operation. To install the batteries, simply depress the back
of the remote with your thumb on the spot marked OPEN.
Insert batteries according to the diagram shown inside.
Replace Cover.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and injury to persons,
including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance directly into a 120 V AC
electrical outlet.
3) Keep the cord out of heavy traffic areas. DO NOT let the cord hang over
the edge of a table or counter. To avoid fire hazard, NEVER put the cord
under rugs, near heat registers, radiator, stoves, or heaters.
4) To protect against electrical hazards, DO NOT immerse in water or other
liquids. Do not use near water.
5) Close supervision is necessary when any appliance is used by or near
children, or by disabled people.
6) Always unplug the fan before moving it, putting on or taking off parts,
cleaning, or whenever the fan is not in use. Be sure to pull by the plug
and not the cord.
7) Avoid contact with moving parts. DO NOT operate without fan grills prop-
erly in place.
8) DO NOT operate any appliance with a damaged cord or plug, if motor fan
fails to rotate, after the appliance malfunctions, or if it has been dropped
or damaged in any manner. Return appliance to manufacturer for
examination, electrical or mechanical adjustment, or repair.
9) DO NOT operate in the presence of explosive and/or flammable fumes.
10) Use appliance only for intended household use as described in this
manual. Any other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons. The use of attachments not
recommended or sold by The Holmes Group may cause hazards.
11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open flames.
14) WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan
with any solid-state speed control device.
15) DO NOT attempt to repair or adjust any electrical or mechanical functions
on this unit. Doing so will void your warranty. The inside of the unit con-
tains no user serviceable parts. All servicing should be performed by
qualified personnel only.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Base / Pole Assembly
Step 1: Push in the small tab on each foot extension and snap into base
Step 2: Remove the base collar from the base by turning
counter-clockwise.
Step 3: Take the pole, with the solid end down, and insert it into the
base. The hollow end of the pole (with the screw hole) will be
facing up.
Step 4: Replace the height adjustment knob over the pole, slide it down
the pole, and secure it to the base by turning clockwise.
Fan Head Assembly
Step 1: Position the rear grill over the motor shaft, making certain the 2
notches at the top and bottom of the rear grill fit over the 2
prongs on the motor housing. Please make sure the rear grill fits
securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear grill mounting-
ring. Turn this ring clockwise and tighten firmly.
Step 3: Slide the fan blade; with the hollowed interior of the blade fac-
ing towards the rear grill firmly onto the motor shaft. Make sure
the shaft protrudes from the front of the blade.
Step 4: Secure the fan blade onto the motor shaft by turning the
fan blade cap in a counter-clockwise direction until it is firmly
in place.
Step 5: Prepare the front grill by simply snapping the circular front grill
logo plate in place.
Step 6: Center the front grill by aligning the Holmes logo so it is hori-
zontal and parallel to the floor. Place the front grill on to the
rear grill and snap into place. Tighten the securing screw at the
bottom of the front grill.
A. LOGO PLATE
B. FRONT GRILL
C. FAN BLADE CAP
D. FAN BLADE
E. REAR-GRILL MOUNTING RING
F. REAR GRILL
G. MOTOR SHAFT
H. MOTOR HOUSING
I. OSCILLATION KNOB
J. NECK
K. TILT-ADJUSTMENT KNOB
L. 1TOUCH
™
FRONT HOUSING
M. 1TOUCH
™
REAR HOUSING
N. THUMBSCEW
O. POLE
P. HEIGHT ADJUSTMENT KNOB
A
B
C
D
E
U
L
Q
P
F
G
H
I
J
K
N
M
O
T
S
R
FIGURE 1
Q. BASE
R. FEET (4)
S. POWER CORD
T. REMOTE CONTROL
U. SECURITY SCREW
FIGURE 2
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zine), or rechargeable (nickel-cadmium) batteries.
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment:
Your fan is equipped with the Total Flex™ tilt adjustment mechanism.
Total Flex™ allows you to angle the fan head to a straight up position.
This position allows for whole room air circulation. Follow these instruc-
tions to tilt the fan head for upward angled air movement or whole-
room air circulation. You may use the oscillation feature in this position.
Step 1: To change the tilting angle of the fan head; simply loosen the Tilt
Adjustment Knob (see figure 1).
Step 2: Move the fan head to the desired angle, and firmly tighten the
knob to lock in place.
Height Adjustment
Step 1: Turn the base collar counter-clockwise to loosen the extension pole.
Step 2: Adjust the extension pole to the desired height, and firmly
tighten the base collar in a clockwise direction.
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for your Holmes
stand fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline, thinner, benzine
(See instructions for fan head assembly)
Step 1: To access the fan blade, remove the front grill and the fan blade
nut.
Step 2: Clean the fan blade, both front and rear grills with a soft cloth
moistened with a mild soap solution.
Step 3: Replace blade, tighten the blade nut, and securely fasten the
front grill.
Fan Head, Base, and Pole Cleaning
Using a soft, moist cloth, with or without a mild soap solution, carefully
clean the fan base, pole, and head. Please use caution around the motor
housing area. Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
Your fan can be stored in the off-season either partially disassembled or
assembled. It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using the original
(or appropriately sized) box.
• If stored assembled or partially assembled, remember to protect the
fan head from dust.
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current) PLUG (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not fit, contact
qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
H-H158.01 HASF1796RC_m 12.04.2001 02.03pm Page 2