Filter
Top Products
Final Assembly
Step 1: Place the hollow end of the remote control hous-
ing on to the upper pole until it will not go down
any further.
Step 2: Tighten the locking nut on the back of the remote
control housing by turning it clockwise until the
fan head assembly is secure.
FIGURE 1
A. Logo Plate
B. Front Grill
C. Grill Caps
D. Fan Blade Cap
E. Fan Blade
F. Rear Grill
Mounting-ring
G. Rear Grill
H. Motor Shaft
I. Motor Housing
J. Remote Control
Housing
K. Remote Control
L. Thumb Screw
M. Upper Pole
N. Lower Pole
O. Base
P. W eight
Q. Weight Nut
A
B
C
D
E
F
G
H
I
K
L
J
M
N
O
P
Q
Fan Head Assembly
Step 1: Position the rear grill over the motor shaft,
making certain the 2 notches at the top and
bottom of the rear grill fit over the 2 protruding
notches on the motor housing. Please make sure
the rear grill fits securely against the motor housing.
Step 2: Fasten the rear grill in place using the rear grill
mounting-ring. Turn the ring clockwise and tighten
firmly.
Step 3: Slide the fan blade; with the hollowed interior of
the fan blade facing toward the rear grill firmly
onto the motor shaft. Make sure that the motor
shaft protrudes from the front of the blade.
Step 4: Secure the fan blade onto the motor shaft by
turning the fan blade cap counter-clockwise.
Tighten until secure.
Step 5: Snap the logo plate on to the front grill, making
sure the clips on the logo plate, fit into the open-
ings on the front grill.
Step 6: On the front grill, lift the grill clips up so that
there is no interference when placing the front
grill onto the rear grill. Center the front grill,
aligning the Holmes logo so it is horizontal and
parallel to the floor. Hang the front grill onto the
rear grill and close all of the clips until the two
grills are secured.
ASSEMBLY INSTRUCTIONS:
Base / Pole Assembly
Step 1: Insert the lower pole (longer of the 2 poles) through
the base cover and twist the pole clockwise to lock in
position. Be careful to align the cut-away grooves
on the threaded joint (male end) with the two
protruding raised pieces inside the hollow end of
the base cover.
Step 2: Turn the base cover upside down (with the lower
pole facing the floor) and place the weighted insert
into the base cover. The pole threads will be exposed
as they protrude through the insert.
NOTE: HOLD THE POLE, BASE COVER AND WEIGHTED
INSERT IN ONE HAND WHILE TIGHTENING THE BASE
NUT WITH THE OTHER HAND.
Step 3: Place the base nut on the threaded section and
hand-tighten the base nut to securely fasten the
lower extension pole to the base.
Step 4: Insert the upper pole (shorter of the two poles) with
the threaded joint (male end) into the hollow end of
the lower pole (female end), until both poles meet.
Be careful to align the cutaway / grooves on the
threaded joint (male end) with the two protruding
pieces inside the hollow end of the lower pole
(female end).
Step 5: Turn the upper pole clockwise to lock it securely in
place.
9) DO NOT operate in the presence of explosive and/or
flammable fumes.
10) Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by The
Holmes Group may cause hazards.
11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open
flames.
14) WARNING: To reduce the risk of fire or electric
shock, DO NOT use this fan with any solid-state
speed
control device.
15) DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no
user serviceable parts. All servicing should be
performed by qualified personnel only.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, elec-
tric shock, and injury to persons, including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance
directly into a 120 V AC electrical outlet.
3) Keep the cord out of heavy traffic areas. DO NOT
let the cord hang over the edge of a table or count-
er. To avoid fire hazard, NEVER put the cord under
rugs, near heat registers, radiator, stoves, or heaters.
4) To protect against electrical hazards, DO NOT
immerse in water or other liquids. Do not use
near water.
5) Close supervision is necessary when any appliance
is used by or near children, or by disabled people.
6) Always unplug the fan before moving it, putting on
or taking off parts, cleaning, or whenever the fan
is not in use. Be sure to pull by the plug and not
the cord.
7) Avoid contact with moving parts. DO NOT
operate without fan grills properly in place.
8) DO NOT operate any appliance with a damaged
cord or plug, if motor fan fails to rotate, after the
appliance malfunctions, or if it has been dropped
or damaged in any manner. Return appliance to
manufacturer for examination, electrical or
mechanical adjustment, or repair.
Remote Control Handheld Unit:
Your remote control requires 2 AAA batteries
for operation. To install the batteries, simply
depress the back of the remote with your
thumb on the spot marked OPEN. Insert bat-
teries according to the diagram shown inside.
Replace cover.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zine), or rechargeable
(nickel-cadmium) batteries.
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current) PLUG (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not fit, contact
qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
new HASF1750RC.01.US.OM1 12.04.2001 10.19am Page 2