Filter
Top Products
CLEANING/MAINTENANCE
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance directly into a 120 V AC
electrical outlet.
3) Keep the cord out of heavy traffic areas. DO NOT let the cord hang over
the edge of a table or counter. To avoid fire hazard, NEVER put the cord
under rugs, near heat registers, radiator, stoves, or heaters.
4) To protect against electrical hazards, DO NOT immerse in water or other
liquids. Do not use near water.
5) Close supervision is necessary when any appliance is used by or near
children, or by disabled people.
6) Always unplug the fan before moving it, putting on or taking off parts,
cleaning, or whenever the fan is not in use. Be sure to pull by the plug
and not the cord.
7) Avoid contact with moving parts. DO NOT operate without fan grills
properly in place.
8) DO NOT operate any appliance with a damaged cord or plug, if motor fan
fails to rotate, after the appliance malfunctions, or if it has been dropped or
damaged in any manner. Return appliance to manufacturer for examination,
electrical or mechanical adjustment, or repair.
9) DO NOT operate in the presence of explosive and/or flammable fumes.
10) Use appliance only for intended household use as described in this manual.
Any other use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of attachments not recommended
or sold by Holmes
®
may cause hazards.
11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open flames.
14) WARNING:To reduce the risk of fire or electric shock, DO NOT use this fan
with any solid-state speed control device.
15) DO NOT attempt to repair or adjust any electrical or mechanical functions
on this unit. Doing so will void your warranty. The inside of the unit contains
no user serviceable parts. All servicing should be performed by qualified
personnel only.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current)PLUG (a plug having one blade wider
than the other). This plug will fit into the power outlet
only one way. If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact qualified
personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY.
OPERATING INSTRUCTIONS
Step 1: Set the fan base on a dry, level surface.
Step 2: Please make sure the on/speed knob is in the off position.
Plug cord into any standard 120 volt A/C outlet.
Step 3: The SPEED is adjusted by moving the knob left or right to
the desired setting.
Step 4: The OSCILLATION switch is located to the right of the speed
control knob. To start oscillation, move the switch to the right.
To stop oscillation, move the switch back to the left.
Tilt Adjustment
To change the tilting angle of the fan head, loosen the thumb bolts,
move the fan head to the desired angle, and then re-tighten the thumb
bolts.
Directional Grill Adjustment
Depending upon your cooling needs, you can have the directional fan
grill rotate for more widespread cooling. To have this grill rotate, turn
the rotating grill knob in the center of the grill counter clockwise until
you reach your desired rotation speed. To stop the rotation turn the grill
knob clockwise until it stops rotating.
Follow these instructions to correctly and safely care for your Holmes
power fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline,
thinner, or benzine.
ILLUSTRATIONS
FIGURE 1
A) Fan Head
B) Fan Blade
C) Rotating Grill Knob
D) Thumb Bolts (2)
E) Base
F) Oscillation Switch
G) Speed Control Knob
B
C
A
ASSEMBLY INSTRUCTIONS
Carefully unpack the contents of this carton
Fan Base / Head Assembly
Step 1. Remove the 2 thumb bolts and metal washers from both sides
of the plastic frame. Make sure to leave the 2 rubber washers
where they are.
Step 2. Insert the thumb bolt and metal washer through the side of the
base and into the fan head. Do the same on the opposite side of
the fan head. (figure 2)
D
E
G
F
FIGURE 2
HAPF112201UM2 MANUAL.qxd 10/30/01 1:30 PM Page 2