Filter
Top Products
English
ACCESSORIES (Fig.1)
A Flexible crush proof hose
B Extension pipe
C Curved joint pipe
D Joint pipe
E Cloth bag
F Dusting brush (stored in tool
G Crevice nozzle storage space)
H Rug and floor tool (for CV-S880, CV-T885)
I Rug and floor tool (for CV-S890)
J Rug and floor tool (Y31)
K Rug and floor tool (D321-D)
HOW TO OPERATE
TO ASSEMBLE HOSE (Fig. 2)
The hose and joint pipe are packaged separately. To put them together,
insert the curved joint pipe and joint pipe into each end of the
hose until the claws of the stopper rings click into the holes
of the curved joint pipe and joint pipe.
TO ATTACH HOSE (Fig. 3)
Insert the joint pipe into the suction inlet of the cleaner. When you
remove the hose , pull the joint pipe while pressing the button .
TO ATTACH EXTENSION PIPES (Fig. 4)
Fit the extension pipes , and the selected suction attachment by
twisting together.
TO DETACH EXTENSION PIPES (Fig. 5)
Twist and pull the extension pipe , upward.
RUG AND FLOOR TOOL (Fig. 6) (for CV-S890)
To clean smooth surfaces, depress the switch " " to in line with
" " . To clean rugs or carpets depress the switch " " to in line
with " " .
RUG AND FLOOR TOOL (Fig. 21)
The tool is fitted with a brush at the back which can either be used in
the “withdrawn” or “projected” position. These positions are operated
by the pedal on the tool marked " " (Carpet) and " " (Floor)
For cleaning rug or carpet, keep the brush in its “withdrawn”
position, i.e., with the pedal marked " " pressed down with your
toe. If you feel the tool is heavy to slide on the carpet, please reduce
the suction power by adjusting the suction control. (Fig. 9)
ON-OFF SWITCH (Fig. 7)
Turn cleaner on or off by pushing downward on the power switch .
ELECTRONIC POWER CONTROL (for CV-S890, Fig. 8)
Suction power may be regulated electronically using the dial on the
unit . For stronger suction (thick carpets or hard floors) rotate the
dial to the right. Rotate it to the left for reduced suction (curtains,
delicate fabrics).
SUCTION CONTROL (Fig. 9)
Suction pressure is reduced by moving the adjustment ring on the
curved joint pipe to expose a hole.
The more hole area exposed the lower the suction.
Low suction pressure is recommended for cleaning curtains, blinds,
delicate fabrics etc,.
BAG FULL INDICATOR (Fig. 10)
When the orange sign appears in the large window continuously,
change the cloth bag.
Check the bag full indicator (with the highest power of electronic power
control for CV-S890) by lifting cleaning head from the surface being
cleaned or removing the crevice nozzle when it has been used.
NOTE: If the cleaner is used in such a condition as the orange sign
appears in the large window, air to the motor will be reduced
and the motor will eventually burn out.
AUTOMATIC CORD REWIND (Fig. 11)
The power cord is stored neatly inside the cleaner using an automatic
cord rewind.
When cleaning is completed unplug from the mains and depress the
rewind pedal , the cord will automatically rewind.
NOTE: Should the cord not fully rewind, pull out a short length and
press the pedal again.
For smooth rewinding, turn the cord inlet toward the same direction
as the cord pulled out.
TOOL STORAGE SPACE (Fig. 12)
The crevice and brush tools snap into the rear storage rack for
safekeeping and easy access.
TO USE ATTACHMENTS (Fig. 13,14)
TO STORE ACCESSORIES (Fig. 15)
Hose, extension pipe and rug and floor tool can be attached in
assembled condition to the cleaner by using the nozzle hook of
the rug and floor tool.
This combination allows you a space storage.
1. Place the cleaner upright.
2. Slide the nozzle hook of the rug and floor tool into the hook
supporter at the rear of the cleaner as shown in Fig. 15.
3. Turn the hose around pipes to make it compact and stable.
NOTE:
Do not hold the hose and the joint pipe to transport the cleaner.
TO DISCONNECT CURVED JOINT PIPE (Fig. 16)
Blockages may be cleared by separating the curved joint pipe
from the hose. To separate the curved joint pipe depress the two
claws which are located in the holes on both sides of curved joint
pipe and pull apart.
When needed, the hose collar can be removed from the hose end
by turning it (left-handed screw).
To re-connect push hose back into curved joint pipe and twist until
two claws locate with holes .
Likewise you can disconnect the hose joint on the other end of the hose.
HOW TO REMOVE DUST
TAKING OUT DUST BAG (Fig. 17)
1. Remove the plug from the electrical outlet. Open the bag
compartment lid by pulling up the clamp .
2. Pull out the dust bag gently.
3. Slide off the bag clip from the dust bag and dispose of dust in the
dust bag.
SETTING DUST BAG (Fig. 18)
1. Before setting the dust bag, be sure to slide back the bag clip.
2. Place the dust bag by opening its inner lid .
3. Position the top edges of the collar to the inner lid concave, and
fit the hole at the lower edge to the guide pins of the case.
NOTE
To avoid using the cleaner without the cloth bag, the clamp system of
your cleaner prevents the bag compartment lid from being clamped
when the cloth bag has not been replaced, or has not been set properly
in place.
CARE OF AIR FILTERS
MOTOR PROTECTION AIR FILTER (Fig. 19)
Once or twice a year, or when it becomes visibly soiled, the motor
protection filter located behind the cloth bag may need cleaning.
1. Take out the cloth bag, then remove the filter from the cleaner as
shown in Fig. 19 and wash in warm water.
2. After washing the filter, dry thoroughly away from direct sunlight
and fit back into the cleaner.
5
1
J1861_CV-S880(E) 15/07/2004, 4:07 PM2