Filter
Top Products
Specifications Information and Replacement Parts Manual 4445-95, 4446-95, 5570-95,
5571-95, 5572-95
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble,
operate or maintain the product described. Protect yourself and others by observing all safety information. The Safety Instructions are contained
in the General Operating Instructions. Failure to comply with the safety instructions accompanying this product could result in personal injury
and/or property damage! Retain instructions for future reference.
Vertical Sealless Sprayer/Washer
Pumps
Refer to form 1608-634-00 for General Operating and Safety Instructions and applicable Warranty.
Description
Vertical sealless sprayer/washer pumps are heavy duty industrial units designed for
OEM, automotive and industrial washing machines, parts cleaners, spray booths and
cooling towers. Pumps are immersion type; pump end must be immersed in liquid,
motor must remain above liquid surface.
All models feature 316 stainless steel semi-open clog resistant impeller, stainless steel
shaft, steel shaft coupling, cast iron base and column, plated steel inlet screen, and a
TEFC (Totally Enclosed Fan Cooled) electric motor. Motor has ball bearings. Heavy-
duty steel universal mounting brackets included. Pump design eliminates a bottom
bearing and a shaft seal on all models. Pumps handle liquids up to a maximum
temperature of 200° F. Maximum ambient temperature 104° F. Liquid viscosity cannot
exceed 100 SSU. These are manual units; no controls are supplied. For use with
nonflammable liquids compatible with pump component materials.
Specifications
DRIVER NEMA DIS. Outlet Weight
Model HP Power Supply RPM Frame (Inches)* (Lbs.)
4445-95 3 230 VAC, 60 Hz. 1-phase 3450 56C 1-½ 78
4446-95 3 230 VAC, 60 Hz. 3-phase 3450 56C 1-½ 73
5570-95 10 230/460 VAC, 60 Hz. 3-phase 3450 184JM 1-½ 165
5571-95 7.5 230/460 VAC, 60 Hz. 3-phase 3450 184JM 1-½ 150
5572-95 5 230/460 VAC, 60 Hz. 3-phase 3450 184JM 1-½ 130
NOTE: Driver data is subject to change without notice, see label on driver for actual specifications.
(*) Standard NPT (female) pipe thread
Performance Chart
GPM of Water at Total Head in Feet Max.
Model HP 60 70 80 90 100 110 120 130 140 150 Head†
4445-95 3 80 55 25 - - - - - - - 85 ft.
4446-95 3 80 55 25 - - - - - - - 85 ft.
5572-95 5 * 115 100 80 50 - - - - - 110 ft.
5571-95 7.5 * * 140 125 110 90 70 40 - - 140 ft.
5570-95 10 * * * 162 150 135 120 95 70 40 160 ft.
(*) Operation of pumps beyond range indicated will result in reduced pump life, pump damage and/or motor damage.
(†) Shut-off; convert to psi, multiply by specific gravity and divide by 2.31
Installation
1. (5570 series pumps) Remove
shipping fixture (Ref. No. 19) that
holds the drive shaft to the base
before installing pump.
2. Pump must be installed with its
base supporting the entire weight of
the pump.
CAUTION Mounting brackets are
not designed to support the
pump’s weight. Brackets are
designed to prevent tipping.
3. Position pump in tank or reservoir.
Position mounting brackets, align
pipe clearance hole with pump
discharge outlet.
(4445 series pumps)
4. Assemble one piece of sponge tape
(Ref. No. 25) to each clamp bracket
(Ref. No. 24). Attach clamp brackets to
mounting brackets with fasteners
provided (Ref. Nos. 26 and 27). This
will fix the column (Ref. No. 3) in
position.
(5570 series pumps)
4. Adjust lower fasteners (Ref. No. 4)
to bottom of mounting brackets.
Secure pump to mounting brackets
with upper fasteners (Ref. No. 4).
5. Secure mounting brackets to tank
or reservoir. Install an appropriate
fastener in each hole or slot provided.
6. Install the balance of the system.
5570-250-00 03/2006