Filter
Top Products
R
EPLACING EXISTING SHOWERHEAD AND ARM
WITH ALFIE AND WALL OUTLET
• Remove existing showerhead and shower
arm.
• Obtain a ½” male threaded brass nipple.
The nipple should be long enough so that
it extends 5/8” outside the surface of the
finished wall. Wrap both ends of the nipple
with Teflon
TM
tape and install.
• Attach wall outlet (27458001) to the
exposed nipple. Wrap the exposed male
end of the wall outlet with Teflon
TM
tape.
• Place a hose washer in the shorter hose
end connector. Attach the short hose end
connector to the wall outlet. If wrench
tightening is necessary, protect the finish
with a cloth.
• Place a hose washer in the longer hose end
connector. Attach this end to Alfie and hand
tighten.
• Support Alfie with a stationary handshower
support (28321000) or an angle-adjustable
Porter’E handshower support (27504000).
NOTE: ThE abOvE iNsTallaTiON OpTiON shOuld bE
iNsTallEd ONly by a prOfEssiONal plumbEr.
MOUNTING ALFIE ON A WALLBAR WITH WALL
OUTLET
• Remove existing showerhead and
shower arm.
• Obtain a ½” male threaded brass
nipple. The nipple should be long
enough so that it extends 5/8” outside
the surface of the finished wall. Wrap
both ends of the nipple with Teflon
TM
tape and install.
• Install wall outlet (27458001) to the
nipple.
• Install wallbar Unica’B (27702000)
or Unica’S (27712000) at the desired
height.
• Wrap the wall outlet nipple with
Teflon
TM
tape. Place a hose washer in
the shorter hose end connector. Screw
this end to the wall outlet. Place a
hose washer in the longer hose end
connector. Attach this end to Alfie and
hand tighten..
• Sit Alfie in the holder on the wallbar.
NOTE: ThE abOvE iNsTallaTiON OpTiON shOuld bE
iNsTallEd ONly by a prOfEssiONal plumbEr.
existing handshower, snap-on connector
(28346000) can be specified.
NOTE: Disconnect the Alfie handshower
from the hose by depressing the button.
Handshowers with the snap-on connector
are not recommended for use by children,
who may accidentally disconnect the
handshower while in use.
REPLACING EXISTING SHOWERHEAD AND ARM
WITH ALFIE AND PORTER’E HANDSHOWER SUPPORT
AND HOSE
• Remove existing showerhead and shower
arm.
• Obtain a ½” male threaded brass nipple.
The nipple should be long enough so that
it extends 5/8” outside the surface of the
finished wall. Wrap both ends of the nipple
with Teflon
TM
tape and install.
• Install the Porter’E with outlet (27508001)
mounting piece according to the installation
instructions included with it. Install the
cover. Wrap the outlet threads with Teflon
TM
tape.
• Place a hose washer to the shorter hose end
connector Attach this end to the Porter’E.
Wrench tighten if desired, but use a cloth
to protect the finish on the hose and on the
Porter’E.
• Place a hose washer to the longer hose end
connector. Attach this end to Alfie and hand
tighten.
• Sit Alfie in the holder.
NOTE: ThE abOvE iNsTallaTiON OpTiON shOuld bE
iNsTallEd ONly by a prOfEssiONal plumbEr.
SNAP-ON CONNECTOR SET 28346000
If Alfie is to be used as an accessory to an