Filter
Top Products
8
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Ch pR o G R a m m i N G t h e
R
e m o t e Co N t R o l
Programming 1:
A
To program one Button of a Remote Control (Figure 11):
• Locate Learn Button and Learn Indicator Light near
Terminal Block on Power Head (Figure 12).
• Press and release Learn Button. Red Learn Indicator Light
will blink 2 times per second.
• Press Remote Control Button once within 30 seconds. Red
Learn Indicator Light will stay lit.
• Press Remote Control Button again. Red Learn Indicator
Light will go out, indicating that memory is stored.
• Press again to Activate Unit.
B Program each additional Remote using step A above.
aC C e S S o R i e S
Remote Control Operation
A
Press Button on Remote Control. Garage door will move.
B Press Button again. Garage door will stop:
• The door automatically stops at the end of the
open or close cycle.
C Press Button again. Garage door will reverse.
WARNING
A moving garage door may cause serious injury or death.
• Keep people clear of opening while door is moving.
• Do not allow children to play with the Remote Controls.
If the Safety Reverse does not work properly:
• Close the door and disconnect the Opener using the
Emergency Release Cord.
• Do not use the door Opener, Remote Controls, or
Wireless Keypad.
• Refer to the door and door Opener Owner’s Manuals
before attempting any repairs.
Figure 12 Learn Code Button and Indicator Light.
(Located Lower Right Corner).
OPEN
CLOSE
LEARN
CODE
BUTTON
LEARN
INDICATOR
LIGHT
Figure 11
1-Button and 3-Button
Compact Remotes
w/Docking Station
D
There are several additional varieties of remote controls
available from your local dealer, some equipped with
a flashlight.
A Open garage door using Wall Console.
B Lay a 2” x 4” board flat in center of doorway (Figure 10).
C Close door using Wall Console.
D Check that door stops and reverses within 2 seconds after it
contacts board:
•
If door does not reverse, decrease Close Force until
door reverses (Figure 9).
•
If door still does not reverse, move Limit Switch
toward door.
E Check Safe-T-Beam® System operation:
•
If beam is blocked, door
will not close.
NOTE
The door must contact the 2” x 4” board before the
Carriage activates the Close Limit Switch. If not,
readjust the Close Limit Switch.
Ch
S
e t t i N G Co N t a C t
R
e V e R S e fu N C t i o N
a
D j u S t m e N t
2:
NOTE
Limit Switch and Force Adjustments must be completed before
checking the contact reverse function.
2” x 4” board
laid flat
Figure 10
Checking
Contact
Reverse
NOTE
• Each Remote Control must be programmed
separately.
• The Remote Controls will not close the garage with
malfunctioning Safe-T-Beam® System.
• Program Remote Controls, while at least 24” from
Antenna Wire.
• If the red Learn Indicator Light blinks rapidly,
programming stopped. Restart programming.
• Each Button on a multi-button Remote Control is
for a different Opener. Cannot use more than one
Button for same Opener.
• A maximum of seven Remote Controls or Wireless
Keypads can be stored into the Receiver at one
time. If a Remote Control becomes lost, or if you
want to delete a Remote Control or Wireless
Keypad, see “To Erase All Receiver Memory.”
To Erase All Remotes from Power Head Memory
A Press and hold Learn Button on Power Head for 10 seconds
or until Learn Indicator Light goes out. Memory is erased:
• Program Remotes again as needed.
To Replace Remote Control Battery
A FOR NON-FLASHLIGHT MODELS
• Pop off the back of the transmitter.
–
Use coin, pen, screwdriver or any similar device.
–
Replace old Battery with new coin type battery.
• Replace back of remote.
B FOR FLASHLIGHT MODELS
• Slide open battery cover.
– Replace old Battery with new AAA battery.
• Replace battery cover.