Stovax 7075Bl Stove User Manual


 
11
This is a list of the maintenance products you may need to use
These products, all available from your local Stovax dealer,
along with regular maintenance and use of the correct
fuels, will help you to keep your stove in the best possible
condition.
4.15 If you require more information about Stovax group
products visit our web site www.stovax.com
4.16 When using the stove for the first time again it is best to
burn the fire at a low output for the first day of use. This
will allow the new seals to settle and all new fixing glues
and paint to fully cure.
4.17 During this time, the stove may give off some unpleasant
odours, and we recommend that you keep the room well
ventilated during this period to avoid a build-up of fumes.
4.18 If you require help, your local Stovax dealer will be able to
carry out all of your service and maintenance requirements
for a reasonable cost.
MAINTENANCE and SERVICING
6.1 As part of the routine maintenance of the stove you may
have to remove the firebricks from the stove. This can be
carried out without the use of tools.
6.2 Allow the stove to cool fully before removing firebricks.
6.3 Care should be taken when handling bricks, as they can
become fragile after a period of use. This is normal and the
life will depend on the type of fuels burnt and the level of
use.
6.4 Damaged bricks should be replaced as soon as possible.
HUNTINGDON 25
6.5 To remove the firebricks first remove the side bricks and
then slide the rear bricks forward and then remove these.
HUNTINGDON 28, 30 & 35
6.6 To remove the bricks lift the LH baffle brick, slide the RH
baffle under the LH baffle to allow you to remove, then
remove the LH baffle brick. Remove the LH and RH side
bricks then the back brick. Fitting is the reverse of this
procedure.
HUNTINGDON 40
6.7 Remove side bricks by pulling base of brick towards centre
of stove and repeat for opposite side. Remove rear brick.
Fitting is reverse of the procedure.
7.1 To maintain safe and efficient combustion the stove is fitted
with a baffle in the top of the firebox.
7.2 Allow the stove to cool fully before removing baffle system.
7.3 To remove the baffle, remove the log guard from the stove
to give access to the firebox.
7.4 Care should be taken when handling bricks, as they can
become fragile after a period of use. This is normal and the
life will depend on the type of fuels burnt and the level of
use.
7. FITTING AND REMOVAL OF BAFFLE
(2 PARTS)
6. FITTING & REMOVAL OF FIREBRICKS
(2 SIDES - 1REAR)
Task Product name
Stovax Code
Number
Glass cleaning
Stove glass cleaner 500ml
(wipe on)
4111
Stove glass cleaner
(spray on)
4103
Preventing build-
up of creosote in
flue
Protector (15 sachets) 7002
Protector (1kg tub) 7025
Sealing flue pipe
joints
Fire Cement (500g tub) 2020
Fire Cement (600g cartridge) 2021
Re-painting
Thermolac Black
(400ml aerosol)
2019
Thermolac Black
(200ml brush-on)
2057
Cleaning matt
black stoves
Colloidal black (85ml) 7000
Protecting your
hands
Heat resistant leather gloves 4008
Door sealing rope
14mm Black rope seal
(handy pack)
5000
14mm Black rope seal
(25m reel)
4670
Glass sealing tape
3mm Black rope seal
(handy pack)
4975
3mm Black rope seal
(25m reel)
4974
Thermic seal glue
(50ml bottle) 5037
Soft rope
10mm diameter 4965
Ash Clean
Vaccuum Cleaner Attachment 2091
5. REMOVAL OF THE LOG GUARD
5.1 Remove the log guard by lifting clear of the supporting
brackets and rotating to clear the sides of the door opening.
The stove should not be used without the log guard in
position.