Stovax 7061Bl Stove User Manual


 
12
MAINTENANCE and SERVICING
7.5 It is important to remove and clean the baffle system to
ensure the flue ways are clear of soot and debris and to
ensure the safe and efficient operation of the stove. The
frequency of cleaning will depend on the stove operating
conditions.
7.6 Replace any damaged baffles immediately.
7.7 Do not modify the baffle system.
HUNTINGDON 25
7.8 To remove the baffle, lift the baffle plate, rotate it and then
slide it out through the front.
HUNTINGDON 28, 30 & 35
7.9 To remove the bricks lift the LH baffle brick, slide the RH
baffle under the LH baffle to allow you to remove, then
remove the LH baffle brick. Remove the LH and RH side
bricks then the back brick. Fitting is the reverse of this
procedure.
HUNTINGDON 40
7.10 Side bricks must be removed first.
Remove side bricks by pulling base of brick towards centre
of stove and repeat for opposite side. Remove rear brick.
Fitting is reverse of the procedure.
7.11 Lift LH baffle brick as high and as far forward as possible,
slide RH baffle brick under LH baffle brick and lower
into stove. Repeat for LH brick. Fitting is reverse of the
procedure.
8.1 To maintain the safe use of your stove you may need to
replace a damaged door glass. To complete this operation,
use this method.
8.2 Remove the door, by opening, removing the hinge pins and
lifting the door free of the hinge blocks. Then lie the door
face down on a soft flat surface, to protect the paintwork
and glass.
8.3 Using a screwdriver remove the glass clip fixing screws. The
old glass can then be lifted clear of the door. (Note how
the 3mm sealing rope is placed between the glass and the
door.) Remember to dispose of the old glass safely.
8.4 Clean and re-paint the rear of the door if required. Clean
the screws with light oil and coat with high temperature
anti-seize grease, this will aid future removal.
8.5 Fit a new sealing rope between the new glass and the door,
and place the glass into position in the door. Place the glass
fixing clips in to position and re-fix with the clean fixing
screws, tighten the screws evenly until the clips hold the
8. FITTING A NEW DOOR GLASS
ALL MODELS
glass. Do not over tighten the clips as this could break the
glass.
8.6 Fit only original Stovax ceramic glass, which is suitable to
use in high temperature applications.
8.7 Using the stove with a damaged door glass could cause
dangerous fumes to enter the room, or the stove to overfire,
resulting in damage.
9.1 To maintain the safe use of your stove you may need to
replace a damaged or worn door sealing rope. To complete
this operation, use this method.
9.2 Remove the door from the stove, by opening, removing
the hinge pins and lifting the door free of the hinge blocks.
Then lie the door face down on a soft flat surface, to protect
the paintwork and glass.
9.3 Remove the old rope and scrape old glue from the locating
groove. Clean the locating groove with a clean dry cloth to
remove all old dust and debris.
9.4 Squeeze a generous bead of fresh Stovax Thermic Seal glue
into the rope locating groove. Press the new Stovax rope
into the locating groove, placing the joint in the middle of
the lower edge of the door.
9.5 Refit the door and close the door to apply pressure to the
new rope. Leave the stove closed for at least 12 hours
before lighting the stove and using at a low output for
approximately one day.
9.6 Using the stove with a damaged door seal could cause
dangerous fumes to enter the room, or the stove to overfire,
resulting in damage.
10.1 To maintain the safe use of your Huntingdon stove, you
may need to adjust the door hinges to ensure safe correct
closing of the door. This is completed by loosening the
hinge fixing screws and moving the hinge position, then
tightening the fixing screws.
If you require help, your local Stovax dealer will be able to
carry out all of your service and maintenace requirements
for a reasonable cost.
9. FITTING A NEW DOOR SEAL
ALL MODELS
10. ADJUSTING DOOR HINGES
28/30/35/40 ONLY