Stovax 7053Bl Stove User Manual


  Open as PDF
of 30
 
24
1.4 Using the appliance for the first time:
•Burn at a low output for the first day of use
This allows the seals, fixing glues and paint to fully cure.
1.5 During this time the appliance may give off some
unpleasant odours:
•Keeptheroomwellventilatedtoavoidabuild-upof
fumes.
1.6 Your Stovax dealer can carry out service and maintenance.
2. REMOVAL OF THE LOG GUARD
2.1 To remove the Log guard:
•LiftLogGuardclearofthesupportingbrackets
•Rotatetoclearthesidesofthedooropening.
Do not use appliance without the log guard in position.
3. FITTING AND REMOVAL OF THE
FIREBRICKS
3.1 See Section 3 Fitting & Removal of Firebricks in Installation
section.
4. FITTING AND REMOVAL OF BAFFLE
4.1 See Section 4 Fitting & Removal of Baffle in Installation
section.
5. FITTING AND REMOVAL OF
THE RIDDLING MECHANISM (Multi-fuel only)
5.1 See Section 5 Fitting & Removal of Riddling Mechanism in
Installation section.
6. FITTING A NEW DOOR GLASS
ALL MODELS
6.1 To maintain the safe use of your appliance you may need to
replace a damaged door glass. To complete this operation:
•Removethedoor,byopening,removingthehingepins
and lifting the door free of the hinge blocks
•Laythedoorfacedownonasoftflatsurface,toprotect
the paintwork and glass
•RemovetheglassclipfixingscrewsTheoldglasscanthen
be lifted clear of the door. (Note how the 3mm sealing rope
is placed between the glass and the door.) Dispose of the
old glass safely.
•Cleanandre-painttherearofthedoorifrequired
Clean the screws with light oil and coat with high
MAINTENANCE and SERVICING
temperature anti-seize grease, this will aid future removal.
•Fitanewsealingropebetweenthenewglassandthe
door, and place the glass into position in the door
•Placetheglassfixingclipsintopositionandre-fixwith
the clean fixing screws, tighten the screws evenly until the
clips hold the glass
Do not over tighten the clips as this could break the glass.
6.2 Fit only original Stovax ceramic glass, which is suitable to
use in high temperature applications.
6.3 Using the appliance with a damaged door glass could cause
dangerous fumes to enter the room, or the appliance to
overfire, resulting in damage.
7. FITTING A NEW DOOR SEAL
ALL MODELS
7.1 To maintain the safe use of your appliance you need to
replace damaged or worn door sealing rope. To complete
this operation:
•Removethedoorfromtheappliance,byopening,
removing the hinge pins and lifting the door free of the
hinge blocks
•Laythedoorfacedownonasoftflatsurface,toprotect
the paintwork and glass
•Removetheoldropeandscrapeoldgluefromthe
locating groove
Clean the locating groove with a clean dry cloth to remove
all old dust and debris.
•SqueezeagenerousbeadoffreshStovaxThermicSeal
glue into the rope locating groove
•PressthenewStovaxropeintothelocatinggroove,
placing the joint in the middle of the lower edge of the
door
•Refitthedoorandclosethedoortoapplypressuretothe
new rope
•Leavetheapplianceclosedforatleast12hoursbefore
lighting the appliance and using at a low output for
approximately one day
7.2 Using the appliance with a damaged door seal can cause
dangerous fumes to enter the room, or the appliance to
overfire, resulting in damage.
 previous next