Filter
Top Products
En-8
TIMER OPERATION
Before using the timer function, be sure that the Remote Controller is set to the correct current time (☞ P. 5).
To Use the ON timer or OFF timer
1
Press the START/STOP button (Fig. 6 P)
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3
5
) will light.
2
Press the TIMER MODE button (Fig. 6 M) to select the
OFF timer or ON timer operation.
Each time the button is pressed the timer function changes in the following
order:
▲
▲
▲
▲
CANCEL
PROGRAM (OFF ON, OFF ON)
OFF ON
The indoor unit’s green TIMER Indicator Lamp (Fig. 3 6) will light.
3
Use the TIMER SET buttons (Fig. 6 N) to adjust the
desired OFF time or ON time.
Set the time while the time display is fl ashing (the fl ashing will continue for
about fi ve seconds).
button: Press to advance the time.
button: Press to reverse the time.
About fi ve seconds later, the entire display will reappear.
To Use the Program timer
1
Press the START/STOP button (Fig. 6 P).
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light.
2
Set the desired times for OFF timer and ON timer.
See the section “To Use the ON timer or OFF timer” to set the desired mode
and times.
About three seconds later, the entire display will reappear.
The indoor unit’s TIMER Indicator Lamp (green) (Fig. 3 6) will light.
3
Press the TIMER MODE button (Fig. 6 M) to select the
PROGRAM timer operation (OFF ON or OFF ON
will display).
The display will alternately show “OFF timer” and “ON timer”, then change to
show the time setting for the operation to occur fi rst.
● The program timer will begin operation. (If the ON timer has been selected
to operate fi rst, the unit will stop operating at this point.)
About fi ve seconds later, the entire display will reappear.
About the Program timer
● The program timer allows you to integrate OFF timer and ON timer operations in a
single sequence. The sequence can involve one transition from OFF timer to ON timer,
or from ON timer to OFF timer, within a twenty-four hour period.
● The fi rst timer function to operate will be the one set nearest to the current time. The
order of operation is indicated by the arrow in the Remote Controller’s Display (OFF
ON, or OFF ON).
● One example of Program timer use might be to have the air conditioner automatically
stop (OFF timer) after you go to sleep, then start (ON timer) automatically in the morn-
ing before you arise.
To Cancel the Timer
Use the TIMER button to select “CANCEL”.
The air conditioner will return to normal opera-
tion.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting wait until the entire display reappears,
then press the appropriate buttons to change
the operating condition desired.
To Cancel the Timer
Use the TIMER MODE button to select “CAN-
CEL”.
The air conditioner will return to normal opera-
tion.
To Change the Timer Settings
1.
Follow the instructions given in the section “To
Use the ON Timer or OFF Timer” to select the
timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF ON or OFF ON.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting, SUPER
QUIET mode), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
9315345394_OM.indb 89315345394_OM.indb 8 9/30/2010 2:44:24 PM9/30/2010 2:44:24 PM