First Alert SA340 Smoke Alarm User Manual

Open as PDF

of 1

USER’S MANUAL

Printed in Mexico

M08-0143-002 J1 05/07

INTRODUCTION

Thank you for choosing First Alert

for your Smoke Alarm needs. You

have pur

chased a state-of-the-art Smoke Alarm designed to provide

you with early war

ning of a fire. Please take the time to read this manual

and make the Smoke Alarm an integral part of your family’s safety plan.

Key Featur

es of the SA340 Smoke Alarm:

amper Resistant Lithium Powercell:

ovides continuous power for

up to 10 years. Power

cell cannot be removed.

Single T

est/Silence Button:

Allows you to test the Alarm or silence

nuisance alarms. Testing the Alarm assures you that the unit is function-

ing

correctly and ready to protect you and your family. The Alarm can

be silenced for up to 10 minutes in the event of a nuisance alarm.

Low power warning: The Alarm will sound a “chirp” once per minute

when the Alarm r

eaches the end of its service life and needs to be

eplaced.

Blinking Power Indicator: Confirms that the Smoke Alarm is r

eceiving

power.

den Corporation.

3901 Liberty Str

eet Road, Aurora, IL 60504-8122

FIRE SAFETY TIPS

Follow safety rules and pr

event hazardous situations: 1) Use smoking

materials properly. Never smoke in bed. 2) Keep matches or lighters

away fr

om childr

en; 3) Stor

e flammable materials in pr

oper containers;

4) Keep electrical appliances in good condition and don’

t overload elec-

trical circuits; 5) Keep stoves, barbecue grills, fireplaces and chimneys

grease- and debris-free; 6) Never leave anything cooking on the stove

unattended; 7) Keep portable heaters and open flames, like candles,

away from flammable materials; 8) Don’t let rubbish accumulate.

Keep alarms clean, and test them weekly. Replace alarms immediately if

they are not working properly. Smoke Alarms that do not work cannot alert

you to a fir

e. Keep at least one working fire extinguisher on every floor, and

an additional one in the kitchen. Have fire escape ladders or other reliable

means of escape fr

om an upper floor in case stairs ar

e blocked.

BEFORE YOU INSTALL THIS SMOKE ALARM

IMPORTANT! Read “Recommended Locations for Smoke Alarms”

and “Locations to A

void for Smoke Alarms” befor

e beginning. This

unit monitors the air, and when smoke reaches its sensing chamber,

it alarms. It can give you more time to escape before fire spreads.

This unit can ONLY give an early warning of developing fires if it is

installed, maintained and located where smoke can reach it, and where

all r

esidents can hear it, as described in this manual. This unit will not

sense gas, heat, or flame. It cannot prevent or extinguish fires.

Understand The Dif

fer

ent T

ype of Smoke Alar

Battery power

ed or electrical? Dif

ferent Smoke Alarms provide

different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms

Fire Safety Professionals recommend at least one Smoke Alarm on

every level of your home, in every bedroom, and in every bedroom

hallway or separate sleeping ar

ea. See “Recommended Locations

For Smoke Alarms” and “Locations To Avoid For Smoke Alarms” for

details.

Know What Smoke Alar

ms Can and Can’

t Do

A Smoke Alarm can help alert you to fir

e, giving you precious time

to escape. It can only sound an alarm once smoke reaches the

sensor. See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes

This Smoke Alarm is designed to be used in a typical single-family

home. It alone will not meet r

equir

ements for boarding houses,

apartment buildings, hotels or motels. See “Special Compliance

Considerations” for details.

WEEKLY TESTING

• NEVER use an open flame of any kind to test this unit. You

might accidentally damage or set fir

e to the unit or to your

home. The built-in test switch accurately tests the unit’

operation as required by Underwriters Laboratories, Inc. (UL).

• If the Alarm ever fails to test properly, replace it immediately.

oducts under warranty may be returned to the manufacturer

for

eplacement. See “Limited W

ranty”.

DO NOT stand close to the Alar

m when the hor

n is sounding.

Exposur

e at close range may be har

mful to your hearing. When

testing, step away when hor

n starts sounding.

It is important to test this unit every week to make sure it is working

properly.

Using the test button is the recommended way to test this

Smoke Alarm. Pr

ess and hold the test button on the cover of the unit

until the alarm sounds (the unit may continue to alarm for a few seconds

after you release the button).

During testing you will hear a loud,

epeating hor

n patter

n: 3 beeps, pause, 3 beeps, pause.

Red LED

flashes.

HOW TO INSTALL THIS SMOKE ALARM

THE PARTS OF THIS SMOKE ALARM

FOLLOW THESE SIMPLE STEPS!

IF THIS SMOKE ALARM SOUNDS

RESPONDING TO AN ALARM

During an alarm, you will hear a loud, repeating horn pattern:

3 beeps, pause, 3 beeps, pause. Red LED flashes.

•

If the unit alarms get everyone out of the house immediately.

•

If the unit alarms and you are not testing the unit, it is warning

you of a potentially dangerous situation that requires your

immediate attention. NEVER ignore any alarm. Ignoring the

alar

m may r

esult in injur

y or death.

•

Use the Silence featur

e to stop an unwanted alar

m (caused by

cooking smoke, etc.), then open a window or fan the smoke

away fr

om the unit. The Smoke Alar

m will r

eset automatically.

WHA

T TO DO IN CASE OF FIRE

•

Don’

t panic; stay calm. Follow your family escape plan.

•

Get out of the house as quickly as possible. Don’

t stop to

get dr

essed or collect anything.

•

Feel doors with the back of your hand befor

e opening them.

If a door is cool, open it slowly. Don’t open a hot door. Keep doors

and windows closed, unless you must escape thr

ough them.

•

Cover your nose and mouth with a cloth (pr

eferably damp).

ake short, shallow breaths.

•

Meet at your planned meeting place outside your home,

and do a head count to make sure everybody got out safely.

• Call the Fire Department as soon as possible from outside.

Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your Fire Department for ideas on making your home safer.

Alarms have various limitations. See "Limitations of Smoke Alarms"

for details.

INSTALL THE MOUNTING BRACKET:

To remove the mounting bracket from the

Smoke Alarm base, hold the Smoke Alarm

base firmly and twist the mounting bracket

counter

clockwise.

Place the bracket on the wall or ceiling where

you want to mount the alarm.

3. Hold the mounting bracket against the ceiling

(or wall) and trace ar

ound the inside of the two

keyhole slots.

Make a mark inside each outline for the drill holes.

Put the unit wher

e it won’t get covered with dust when you drill

the mounting holes.

Using a 3/16-inch (5 mm) drill bit, drill a hole through each

pencil mark.

Insert the plastic screw anchors (in the plastic bag with screws)

into the holes. Tap the screw anchors gently with a hammer, if

necessary, until they are flush with the ceiling or wall.

Line the mounting bracket up over the plastic screw anchors.

9. Screw the mounting bracket to the ceiling or wall through the

mounting slots using the two scr

ews provided.

10.

Tighten both screws all the way.

USING THE SILENCE FEA

TURE

The Silence Featur

e can temporarily quiet an unwanted alarm for up

to 10 minutes. T

o use this featur

e, pr

ess the “T

est/Silence” button. The

Alarm remains functional. The LED will flash every 10 seconds (for up

to 10 minutes) to r

emind you the alarm has been silenced. The flashing

LED will stop when the unit returns to normal operation.

The Silence Feature does not disable the unit—it makes it temporar-

ily less sensitive to smoke. For your safety, if smoke around the unit

is dense enough to suggest a potentially dangerous situation, it

will stay in alar

m, or may r

e-alar

m quickly

. If you do not know the

source of the smoke, do not assume it is an unwanted alarm. Not

responding to an alarm can result in property loss, injury or death.

All First Alert

Smoke Alarms conform to regulatory requirements,

including UL217 and ar

e designed to detect particles of combustion.

Smoke par

ticles of varying number and size are produced in all fires.

Ionization technology is generally mor

e sensitive than photoelectric

technology at detecting small particles, which tend to be produced

in gr

eater amounts by flaming fires, which consume combustible

materials rapidly and spr

ead quickly. Sources of these fires may include

paper burning in a wastebasket, or a grease fire in the kitchen.

Photoelectric technology is generally mor

e sensitive than ionization

technology at detecting lar

ge particles, which tend to be pr

duced in gr

eater amounts by smoldering fires, which may smolder

for hours before bursting into flame. Sources of these fires may include

cigar

ettes burning in couches or bedding.

For maximum pr

otection, use both types of Smoke Alar

ms on each

level and in ever

y bedroom of your home.

•

This unit will not aler

t hearing impaired residents. It is recom-

mended that you install special units which use devices like

flashing str

obe lights to alert the hearing impaired residents.

• Do not connect this unit to any other alarm or auxiliary device.

It is a single-station unit that cannot be linked to other devices.

Connecting anything else to this unit may pr

event it fr

om working

properly.

•

This Smoke Alarm cannot detect smoke until you activate it.

ou must activate the unit for it to r

eceive power fr

om the

powercell. Failure to activate the unit will prevent the alarm

from providing any warning of smoke or fire.

• The powercell in this unit cannot be replaced—once it reaches

the end of its ser

vice life, you must install a new Smoke Alarm.

ou must deactivate the unit before disposing of it.

• Do not install this unit over an electrical junction box. Air currents

around junction boxes can prevent smoke from reaching the

sensing chamber and prevent the unit from alarming. Only AC

powered units are intended for installation over junction boxes.

• Do not stand too close to the unit when the alarm is sounding.

It is loud to wake you in an emergency. Exposure to the horn at

close range may harm your hearing.

• Do not paint over the unit. Paint may clog the openings to the

sensing chamber and prevent the unit from operating properly.

2 3

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but

ther

e ar

e a few simple things you must do to keep it working pr

operly

• Test it at least once a week.

•

Clean the Smoke Alarm at least once a month; gently vacuum the

outside of the Smoke Alarm using your household vacuum’s soft

brush attachment. A can of clean compressed air (sold at computer

or of

fice supply stor

es) may also be used. Follow manufactur

instructions for use. Test the Smoke Alarm. Never use water,

cleaners or solvents since they may damage the unit.

• If the Smoke Alarm becomes contaminated by excessive dirt, dust

and/or grime, and cannot be cleaned to avoid unwanted alarms,

replace the unit immediately.

• Relocate the unit if it sounds frequent unwanted alarms. See

“Locations to A

void For Smoke Alarms” for details.

When the powercell becomes weak, the Smoke Alarm unit will “chirp”

about once a minute (the low power war

ning). This low power war

ning

should last for 30 days, but you should r

eplace the Smoke Alarm

immediately to continue your protection.

1. Test/Silence button

2. Power/alarm indicator LED

1. Mounting bracket

2. Mounting slots

3. Powercell

4. Deactivation Tab (located under label)

5. T

urn to attach to bracket

6. Turn this way to remove from bracket

INSERTING THE POWERCELL:

ou must activate the powercell before attaching the Smoke

Alar

m to the bracket.

1. Turn Alarm upside down. Line up

the pins and snap the power

cell

into the Alarm.

2. The powercell cannot be removed

after it is locked into the Alarm.

If you have tr

ouble activating the

unit, call Consumer Affairs at:

1-800-323-9005 for assistance.

Test the Smoke Alarm. Press and hold the test button on the

cover of the unit until the alarm sounds (the unit may continue

to alarm for a few seconds after you r

elease the button).

During testing, you will hear a loud, r

epeating horn pattern:

3 beeps, pause, 3 beeps, pause.

If the unit does not alarm

during testing, call Consumer Af

fairs for assistance.

ATTACH SMOKE ALARM TO MOUNTING BRACKET

Line up the alignment tab on the unit with the alignment tab on

the mounting bracket. Push the unit toward the bracket, and

tur

n it clockwise until you feel it snap into place.

Test the unit again. Press the test button until the horn begins

sounding.

During testing, you will hear a loud, r

epeating

horn pattern: 3 beeps, pause, 3 beeps, pause.

TO PERMANENTLY DEACTIVATE THE SMOKE ALARM

Alarm is sealed. The powercell is not replaceable. Once it reaches

the end of its service life, or after 10 years—whichever comes first—

you must install a new Smoke Alar

After 10 years or after the “low power war

ning” sounds (whichever

comes first):

Once you deactivate this unit, it will not detect smoke or alarm.

It cannot be r

eactivated. You must install a new unit to continue

your protection. Alarm will resist mounting to the bracket after

deactivation.

2. Use a flathead screwdriver to score

label along dotted line.

3. Use thumb to pull deactivation tab

outwar

d until tab snaps into place.

This will dischar

ge the powercell

and deactivate the unit.

4. Install a new Smoke Alarm

immediately!

TOOLS YOU WILL NEED:

This unit is designed to be mounted on the ceiling,

or on the wall if necessary.

• Pencil

•

Drill with 3/16” (5 mm)

drill bit

• Standard flathead

screwdriver

• Hammer

LIMITED W

ARRANTY

BRK Brands, Inc., ("BRK") the maker of First Alert

brand pr

oducts

warrants that for a period of ten years fr

om the date of purchase, this

oduct will be free from defects in material and workmanship. BRK, at

its option, will repair or replace this product or any component of the

oduct found to be defective during the warranty period. Replacement

will be made with a new or r

emanufactured product or component. If

the product is no longer available, replacement may be made with a

similar pr

oduct of equal or greater value. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of

initial r

etail purchase and is not transferable. Keep the original sales

eceipt. Proof of purchase is required to obtain warranty performance.

BRK dealers, service centers, or retail stores selling BRK products do

not have the right to alter

, modify or any way change the terms and

conditions of this warranty

This warranty does not cover normal wear of parts or damage r

esulting

om any of the following: negligent use or misuse of the product, use on

improper voltage or current, use contrary to the operating instructions,

disassembly

, repair or alteration by anyone other than BRK or an

authorized service center

. Further, the warranty does not cover Acts of

God, such as fire, flood, hurricanes and tornadoes or any batteries that

e included with this unit.

BRK shall not be liable for any incidental or consequential damages

caused by the breach of any express or implied warranty. Except to

the extent pr

ohibited by applicable law, any implied warranty of

merchantability or fitness for a particular purpose is limited in duration

to the duration of the above warranty

. Some states, provinces or

jurisdictions do not allow the exclusion or limitation of incidental or

consequential damages or limitations on how long an implied warranty

lasts, so the above limitations or exclusion may not apply to you. This

warranty gives you specific legal rights, and you may also have other

rights that vary from state to state or province to province.

How to Obtain W

arranty Service

Service:

If service is required, do not return the product to your retailer.

In or

der to obtain warranty service, contact the Consumer Affairs

Division at 1-800-323-9005, 7:30 AM - 5:00 PM Central Standard Time,

Monday thr

ough Friday

. T

o assist us in serving you, please have the

model number and date of pur

chase available when calling.

For Warranty Service return to:

BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906

This Smoke Alarm is designed to operate for 10 years, and is backed

by a 10-year limited warranty

. To date, the actual alarm, however, has

not been tested for 10 years. The power

cell in this Smoke Alarm is not

eplaceable. When it r

eaches the end of its service life, you must r

eplace

the entir

e Smoke Alarm to continue your protection.

IF YOU SUSPECT A PROBLEM

Smoke Alarms may not operate pr

operly because of a dead or weak

power

cell, a build-up of dirt, dust or grease on the Smoke Alarm cover,

or installation in an improper location. Clean the Smoke Alarm as

described in “Regular Maintenance,” and test the Smoke Alarm again.

If it fails to test pr

operly when you use the test button, or if the problem

persists, replace the Smoke Alarm immediately.

• If you experience frequent non-emergency alarms (like those

caused by cooking smoke), tr

y relocating the Smoke Alarm.

•

If the alarm sounds when no smoke is visible, try cleaning or

relocating the Smoke Alarm. The cover may be dirty.

•

If the alarm no longer sounds during testing, replace the

Smoke Alarm! If the Smoke Alarm was properly activated, and

had previously alarmed during testing, the powercell is at the

end of its ser

vice life. (See “Regular Maintenance.”)

• If the alarm will not silence when you use the Silence feature,

DO NOT IGNORE THE ALARM! This indicates a potentially

dangerous situation.

•

If the Smoke Alarm “chirps” about once a minute (for more

than 30 minutes), Replace the Smoke Alar

m! (See “Regular

Maintenance.”) This is the low power warning.

DO NOT TRY FIXING THE ALARM YOURSELF—THIS WILL VOID YOUR WARRANTY!

If the Smoke Alarm is still not operating pr

operly, and it is still under

warranty

, please see “How to Obtain Warranty Service” in the Limited

arranty below.

RECOMMENDED LOCATIONS FOR

SMOKE ALARMS

Installing Smoke Alar

ms in Single-Family Residences

The National Fir

e Pr

otection Association (NFP

A), r

ecommends one

Smoke Alarm on every floor, in every sleeping area, and in every bed-

room. In new construction, the Smoke Alarms must be AC powered

and interconnected. See “Agency Placement Recommendations” for

details. For additional coverage, it is r

ecommended that you install a

Smoke Alarm in all rooms, halls, storage areas, finished attics, and

basements, wher

e temperatur

es normally remain between 40˚ F (4˚ C)

and 100˚ F (38˚ C). Make sure no door or other obstruction could keep

smoke fr

om reaching the Smoke Alarms.

More specifically, install Smoke Alarms:

• On every level of your home, including finished attics and basements.

• Inside every bedroom, especially if people sleep with the door partly

or completely closed.

•

In the hall near every sleeping ar

ea. If your home has multiple

sleeping areas, install a unit in each. If a hall is over 40 feet (12

meters) long, install an alarm at each end.

•

At the top of the first-to-second floor stairway, and at bottom of

basement stairway.

Specific requirements for Smoke Alarm installation vary from state to

state and fr

om region to region. Check with your local Fire Department

for current requirements in your area.

It is recommended AC or AC/DC

units be inter

connected for added protection.

INSTALLING SMOKE ALARMS IN MOBILE HOMES & RVS

For minimum security install one Smoke Alarm as close to each sleeping

area as possible. For more security, put one unit in each room. Many

older mobile homes (especially those built befor

e 1978) have little or no

insulation. If your mobile home is not well insulated, or if you ar

e unsure

of the amount of insulation, it is important to install units on inside walls

only

. Smoke Alarms should be installed where temperatures normally

emain between 40˚ F (4˚ C) and 100˚ F (38˚ C).

ARNING: Test units

used in RVs after the vehicle has been in storage, before every trip,

and once a week while in use. Failure to test units used in RVs as

described may r

emove your protection.

AGENCY PLACEMENT RECOMMENDATIONS

NFPA 72 (National Fire Code) Chapter 11

“For your information, the National Fir

e Protection Association's

Standard 72, reads as follows:”

“11.5.1 One- and T

wo-Family Dwelling Units.”

“11.5.1.1 Smoke Detection.

Where required by applicable laws, codes,

or standar

ds for the specified occupancy, approved single- and multiple

-station Smoke Alarms shall be installed as follows: (1) In all sleeping

ooms. Exception: Smoke Alarms shall not be required in sleeping

ooms in existing one- and two-family dwelling units. (2) Outside of

each separate sleeping area, in immediate vicinity of the sleeping

ooms. (3) On each level of the dwelling unit, including basements.

Exception: In existing one- and two family dwelling units, appr

oved

Smoke Alarms powered by batteries are permitted.”

“A.11.8.3 Are More Smoke Alarms Desirable? The required number

of Smoke Alarms might not pr

ovide r

eliable early warning protection

for those ar

eas separated by a door from the areas protected by the

required Smoke Alarms. For this reason, it is recommended that the

householder consider the use of additional Smoke Alarms for those

eas for increased protection. The additional areas include the base-

ment, bedrooms, dining room, furnace room, utility room, and hallways

not pr

otected by the required Smoke Alarms. The installation of Smoke

Alarms in kitchens, attics (finished or unfinished), or garages is not

normally recommended, as these locations occasionally experience

conditions that can r

esult in improper operation.”

Califor

nia State Fire Marshal (CSFM)

Early war

ning detection is best achieved by the installation of fire detec-

tion equipment in all r

ooms and areas of the household as follows: A

Smoke Alarm installed in each separate sleeping area (in the vicinity, but

outside bedr

ooms), and Heat or Smoke Alarms in the living rooms, din-

ing r

ooms, bedrooms, kitchens, hallways, finished attics, furnace rooms,

closets, utility and storage rooms, basements, and attached garages.

LOCATIONS TO AVOID FOR SMOKE ALARMS

For best per

formance, AVOID installing Smoke Alarms in these areas:

• Where combustion particles are produced. Combustion particles

form when something bur

ns. Ar

eas to avoid include poorly ventilated

kitchens, garages, and furnace rooms. Keep units at least 20 feet

(6 meters) from the sources of combustion particles (stove, furnace,

water heater

, space heater) if possible. In areas where a 20-foot

(6 m) distance is not possible – in modular, mobile, or smaller

homes, for example – it is recommended the Smoke Alarm be

placed as far fr

om these fuel-bur

ning sources as possible. The

placement recommendations are intended to keep these Alarms at

a reasonable distance from a fuel-burning source, and thus reduce

“unwanted” alarms. Unwanted alarms can occur if a Smoke Alarm

is placed directly next to a fuel-burning source. Ventilate these

areas as much as possible.

•

In air streams near kitchens. Air currents can draw cooking smoke

into the sensing chamber of a Smoke Alarm near the kitchen.

•

In very damp, humid or steamy ar

eas, or dir

ectly near bathr

ooms

with showers. Keep units at least 10 feet (3 meters) away fr

showers, saunas, dishwashers, etc.

• Where the temperatures are regularly below 40˚ F (4˚ C) or above

100˚ F (38˚ C), including unheated buildings, outdoor r

ooms, por

ches,

or unfinished attics or basements.

• In very dusty, dirty, or greasy areas. Do not install a Smoke Alarm

dir

ectly over the stove or range. Clean a laundry room unit frequently

to keep it free of dust or lint.

• Near fresh air vents, ceiling fans, or in very drafty areas. Drafts can

blow smoke away fr

om the unit, pr

eventing it fr

om reaching the

sensing chamber.

• In insect infested areas. Insects can clog openings to the sensing

chamber and cause unwanted alarms.

• Less than 12 inches (305mm) away from fluorescent lights.

Electrical “noise” can interfer

e with the sensor

• In “dead air” spaces. “Dead air” spaces may prevent smoke from

reaching the Smoke Alarm.

voiding Dead Air Spaces

“Dead air” spaces may pr

event smoke fr

om r

eaching the Smoke Alarm.

To avoid dead air spaces, follow the installation recommendations below.

On ceilings, install Smoke Alarms as close to the center of the ceiling

as possible. If this is not possible, install the Smoke Alarm at least

4 inches (102 mm) fr

om the wall or cor

ner

For wall mounting (if allowed by building codes), the top edge of Smoke

Alarms should be placed between 4 inches (102 mm) and 12 inches (305

mm) from the wall/ceiling line, below typical “dead air” spaces.

On a peaked, gabled, or cathedral ceiling, install the first Smoke

Alarm within 3 feet (0.9 meters) of the peak of the ceiling, measured

horizontally

. Additional Smoke Alarms may be r

equir

ed depending on

the length, angle, etc. of the ceiling's slope. Refer to NFPA 72 for

details on requirements for sloped or peaked ceilings.

SPECIAL COMPLIANCE CONSIDERA

TIONS

This Smoke Alarm alone is not a suitable substitute for complete fir

detection systems in places housing many people—like apartment

buildings, condominiums, hotels, motels, dormitories, hospitals, long-

term health car

e facilities, nursing homes, day care facilities, or group

homes of any kind—even if they were once single-family homes.

It is not a suitable substitute for complete fir

e detection systems in

war

ehouses, industrial facilities, commercial buildings, and special-

purpose non-residential buildings which require special fire detection

and alarm systems. Depending on the building codes in your ar

ea, this

Smoke Alarm may be used to pr

ovide additional protection in these

facilities.

The following information applies to all four building types below:

In new construction, most building codes require the use of AC or AC/DC

power

ed Smoke Alarms only. AC, AC/DC, or DC powered Smoke Alarms

can be used in existing construction as specified by local building codes.

Refer to NFPA 72 (National Fire Alarm Code) and NFPA 101 (Life Safety

Code), local building codes, or consult your Fir

e Department for detailed

fire protection requirements in buildings not defined as “households.”

1. Single-Family Residence:

Single family home, townhouse. It is r

ecommended Smoke Alarms be

installed on every level of the home, in every bedr

oom, and in each

bedr

oom hallway.

2. Multi-Family or Mixed Occupant Residence:

Apartment building, condominium. This Smoke Alarm is suitable for

use in individual apartments or condos, pr

ovided a primary fire detection

system alr

eady exists to meet fire detection requirements in common

areas like lobbies, hallways, or porches. Using this Smoke Alarm in

common ar

eas may not provide sufficient warning to all residents or

meet local fir

e protection ordinances/regulations.

3. Institutions:

Hospitals, day car

e facilities, long-term health care facilities. This Smoke

Alarm is suitable for use in individual patient sleeping/r

esident rooms,

ovided a primary fire detection system already exists to meet fire

detection requirements in common areas like lobbies, hallways, or

por

ches. Using this Smoke Alarm in common areas may not provide

suf

ficient warning to all residents or meet local fire protection ordinances

/regulations.

4. Hotels and Motels:

Also boarding houses and dormitories. This Smoke Alarm is suitable

for use inside individual sleeping/r

esident rooms, provided a primary

fir

e detection system already exists to meet fire detection requirements

in common areas like lobbies, hallways, or porches. Using this Smoke

Alarm in common ar

eas may not provide sufficient warning to all

esidents or meet local fire protection ordinances/regulations.

LIMIT

ATIONS OF SMOKE ALARMS

Smoke Alarms have played a key r

ole in reducing deaths resulting from

home fir

es worldwide. However, like any warning device, Smoke Alarms

can only work if they are properly located, installed, and maintained, and

if smoke r

eaches them. They are not foolproof.

Smoke alar

ms may not waken all individuals.

Practice the escape

plan at least twice a year

, making sur

e that everyone is involved – from

kids to grandparents. Allow children to master fire escape planning and

practice befor

e holding a fire drill at night when they are sleeping.

If childr

en or others do not r

eadily waken to the sound of the smoke

alarm, or if there are infants or family members with mobility limitations,

make sur

e that someone is assigned to assist them in fir

e drill and in

the event of an emer

gency. It is recommended that you hold a fire drill

while family members are sleeping in order to determine their response

to the sound of the smoke alarm while sleeping and to determine

whether they may need assistance in the event of an emer

gency

Smoke Alar

ms cannot work without power.

DC operated units cannot

work if the power

cell is missing, deactivated, or dead, or if the power

cell

was not activated corr

ectly

. AC units cannot work if the AC power is cut

f for any reason (open fuse or circuit breaker, failure along a power line

or at a power station, electrical fire that burns the electrical wires, etc.).

If you are concerned about the limitations of DC or AC power, install

both types of units.

Smoke Alar

ms cannot detect fires if the smoke does not reach

the Alar

ms.

Smoke fr

om fires in chimneys or walls, on roofs, or on

the other side of closed doors may not r

each the sensing chamber and

set of

f the alarm. That is why one unit should be installed inside each

bedroom or sleeping area—especially if bedroom or sleeping area

doors ar

e closed at night—and in the hallway between them.

Smoke Alarms may not detect fire on another floor or area of the

dwelling. For example, a stand-alone unit on the second floor may not

detect smoke fr

om a basement fir

e until the fir

e spreads. This may not

give you enough time to escape safely. That is why recommended

minimum pr

otection is at least one unit in every sleeping area, and

every bedroom on every level of your dwelling. Even with a unit on

every floor, stand-alone units may not provide as much protection as

inter

connected units, especially if the fir

e starts in a r

emote ar

ea. Some

safety experts recommend installing interconnected AC powered units

with battery back-up (see “About Smoke Alarms”) or professional fire

detection systems, so if one unit senses smoke, all units alarm.

Inter

connected units may pr

ovide earlier warning than stand-alone

units since all units alarm when one detects smoke.

Smoke Alar

ms may not be hear

Though the alarm hor

n in this unit

meets or exceeds current standards, it may not be heard if: 1) the unit

is located outside a closed or partially closed door, 2) residents recently

consumed alcohol or drugs, 3) the alarm is drowned out by noise from

stereo, TV, traffic, air conditioner or other appliances, 4) residents are

hearing impair

ed or sound sleepers. Special purpose units, like those

with visual and audible alarms, should be installed for hearing impaired

residents.

Smoke Alarms may not have time to alarm before the fire itself

causes damage, injury, or death, since smoke from some fires may

not r

each the unit immediately

. Examples of this include persons

smoking in bed, childr

en playing with matches, or fires caused by

violent explosions resulting from escaping gas.

Smoke Alar

ms are not foolproof.

Like any electr

onic device, Smoke

Alarms are made of components that can wear out or fail at any time.

You must test the unit weekly to ensure your continued protection.

Smoke Alarms cannot pr

event or extinguish fir

es. They ar

e not a

substitute for property or life insurance.

Smoke Alar

ms have a limited life.

The unit should be r

eplaced

immediately if it is not operating properly. You should always replace a

Smoke Alarm after 10 years fr

om date of pur

chase. W

rite the purchase

date on the space provided on back of unit.

First Alert

is a registered trademark of the First Alert Trust.

4 5

ABOUT

SMOKE

ALARMS

Batter

y or DC operated Smoke Alar

ms:

ovide pr

otection even

when electricity fails, provided the batteries or battery packs are fresh

and correctly installed or activated. Units are easy to install, and do not

equir

e pr

ofessional installation.

AC power

ed Smoke Alar

ms:

Can be inter

connected so if one unit

senses smoke, all units alarm. They do not operate if electricity fails.

AC with battery (DC) back-up: will operate if electricity fails, provided

the batteries ar

e fr

esh and corr

ectly installed. AC and AC/DC units

must be installed by a qualified electrician.

Smoke Alarms for Solar or Wind Energy users and battery backup

power systems: AC power

ed Smoke Alarms should only be operated

with true or pur

e sine wave inverters. Operating this Smoke Alarm with

most battery-powered UPS (uninterruptible power supply) products or

squar

e wave or “quasi sine wave” inverters

will damage the Alar

If you are not sure about your inverter or UPS type, please consult with

the manufacturer to verify.

Smoke Alarms for the hearing impaired: Special purpose Smoke

Alarms should be installed for the hearing impaired. They include a

visual alarm and an audible alarm hor

n, and meet the r

equir

ements of

the Americans With Disabilities Act. Can be inter

connected so if one

unit senses smoke, all units alarm.

Smoke alarms are not to be used with detector guards unless the

combination has been evaluated and found suitable for that purpose.

All these Smoke Alarms ar

e designed to pr

ovide early war

ning of fir

es if

located, installed and cared for as described in the user’s manual, and if

smoke r

eaches them. If you are unsure which type of unit to install, refer

to Chapter 2 of the National Fire Protection Association (NFPA) Standard

72 (National Fire Alarm Code) and NFPA 101 (Life Safety Code).

National Fire Protection Association, One Batterymarch Park, Quincy,

MA 02269-9101. Local building codes may also require specific units in

new construction or in different areas of the home.

BEDROOM

HALL

LIVING ROOM KITCHEN

FINISHED BASEMENT

REQUIRED TO MEET

NFPA RECOMMENDATIONS

RECOMMENDED FOR

ADDITIONAL PROTECTION

BEDROOM

KITCHEN

LIVING ROOM

DINING ROOM

MULTI-STORY RESIDENCE

SINGLE-STORY RESIDENCE, APARTMENT,

MOBILE HOME

KEY:

EXISTING HOMES

SMOKE ALARMS WITH SILENCE

FEATURES RECOMMENDED FOR

ADDITIONAL PROTECTION

BEDROOM

HALL

LIVING ROOM KITCHEN

FINISHED BASEMENT

BEDROOM

LIVING ROOM

DINING ROOM

MULTI-STORY RESIDENCE

SINGLE-STORY RESIDENCE, APARTMENT,

MOBILE HOME

EXISTING HOMES

KITCHEN

REQUIRED TO

MEET NFPA

RECOMMENDATIONS

RECOMMENDED

FOR ADDITIONAL

PROTECTION

KEY:

SMOKE ALARMS WITH SILENCE

FEATURES RECOMMENDED FOR

ADDITIONAL PROTECTION

INTERCONNECTED

AC OR AC/DC

SMOKE ALARMS

BEDROOM

HALL

LIVING ROOM KITCHEN

FINISHED BASEMENT

REQUIRED TO

MEET NFPA

RECOMMENDATIONS

RECOMMENDED

FOR ADDITIONAL

PROTECTION

BEDROOM

LIVING ROOM

DINING ROOM

MULT I-STORY RESIDENCE

SINGLE-STORY RESIDENCE, APARTMENT,

MOBILE HOME

KEY:

NEW CONSTRUCTION

SMOKE ALARMS

WITH SILENCE

FEATURES

RECOMMENDED

FOR ADDITIONAL

PROTECTION

KITCHEN

Printed in Mexico M08-0143-002 J1 05/07

Replace Alarm 10 years after installation. Write the replacement

date in the space pr

ovided

on the Alar

m label.

For your r

ecor

ds, please r

ecor

Date Purchased: _______________________________

Date Installed: ___________/____________Month/Y

ear

Replacement Date: ___________/____________Month/Y

ear

SMOKE ALARM WITH TEN-YEAR

NON-REPLACEABLE LITHIUM POWERCELL

Model SA340

IMPORTANT! PLEASE READ

CAREFULL

Y AND SAVE.

This user’

s manual contains

important information about

your Smoke Alarm’s operation.

If you ar

e installing this Smoke

Alarm for use by others, you

must leave this manual—or a

copy of it—with the end user

Model SA340

Top Automotive Device Types

Top Automotive Brands

Top Baby Care Device Types

Top Baby Care Brands

Top Car Audio & Video Device Types

Top Car Audio & Video Brands

Top Cellphone Device Types

Top Cellphone Brands

Top Communications Device Types

Top Communications Brands

Top Computer Device Types

Top Computer Brands

Top Fitness Device Types

Top Fitness Brands

Top Home Audio Device Types

Top Home Audio Brands

Top Household Appliance Device Types

Top Household Appliance Brands

Top Kitchen Appliance Device Types

Top Kitchen Appliance Brands

Top Laundry Appliance Device Types

Top Laundry Appliance Brands

Top Lawn & Garden Device Types

Top Lawn & Garden Brands

Top Marine Equipment Device Types

Top Marine Equipment Brands

Top Musical Instrument Device Types

Top Musical Instrument Brands

Top Outdoor Cooking Device Types

Top Outdoor Cooking Brands

Top Personal Care Device Types

Top Personal Care Brands

Top Photography Device Types

Top Photography Brands

Top Portable Media Device Types

Top Portable Media Brands

Top Power Tools Device Types

Top Power Tools Brands

Top TV and Video Device Types

Top TV and Video Brands

Top Videogame Device Types

Top Videogame Brands

First Alert SA340 Smoke Alarm User Manual