Filter
Top Products
firstalert.com
ARCHITECTURAL AND ENGINEERING SPEC
INSTALLATION OF ALARM
The smoke alarm shall be a First Alert Model SA320 and shall provide at a minimum the
following features and functions:
1. Two smoke sensing chambers - photoelectric and ionization.
2. Powered by two AA alkaline batteries and have a solid state piezo horn rated at
85dB at 10 ft. and shall be capable of self restoring.
3. A visual power-on indicator to confirm unit is receiving power.
4. Two Latching features: Alarm Latch to easily identify initiating alarm after alarm
condition has subsided. Low battery latch: to visually identify which unit is in low
battery condition. Two Silence Features: Alarm Silence to temporarily silence
nuisance alarms. Low Battery Silence to silence low battery chirp for up to 8 hours.
5. Two Locking features - tamper resistant locking pins that lock battery drawer
and/or alarm to mounting bracket.
6. The unit shall be capable of operating between 40°F (4°C) and 100°F (38°C) and
relative humidity between 10% and 95%.
7. The unit shall contain mounting hardware and shall be listed for wall or ceiling
mounting.
8. The unit shall have a gasketless base for easy install
ation and be capable of
keeping alarm secure over a wide rotation range to allow for true alarm
alignment.
9. The unit shall at a minimum meet the requirements of UL217, CSFM,
NFPA 72 and the ICC.
SHIPPING SPECS:
TECHNICAL SPECS
Individual Carton Dimensions 2.5"L x 7.0"W x 8.5"H
.sbl 37.0 thgieW
4 83700 45092 0 CPU
Master Carton Dimensions 7.7"L x 7.31"W x 9.06"H
Master Pack 3
.sbl .282 thgieW
300 29054 00738 5 :5fo2I
Pallet Information
Cases per Layer 30
Number of Layers: 5
Cases per Pallet: 150
Units per pallet: 450
.sbl 350 :thgieW
©2011 BRK Brands, Inc. a Jarden Corporation
Company (NYSE: JAH)
3901 Liberty Street Road
Aurora, IL 60504-8122
All rights reserved
First Alert is a registered trademark of the First Alert Trust
BRK is a registered trademark of BRK Brands, Inc.
CM3044
CAT.
SA320CN
BATTERY DRAWER LOCK
Remove Pin from
Mounting Bracket
Close Door. Insert Pin in Holes
through alarm and Battery Drawer
5.0"
TOP VIEW SIDE VIEW
MOUNTING
BRACKET
2.0"
THE PARTS OF THIS SMOKE ALARM
BOTTOM OF ALARM
1. Mounting bracket
2. Mounting Slots
3. Battery Drawer - Install
2 AA batteries here
4. Turn this way to
remove from bracket
5. Turn this way to
attach to bracket
TOP OF ALARM
1. Test/Silence button
2. Slide-open
battery drawer
3. Power/Alarm light
Alarm Dimensions: 5.0” dia x 2.0”H
Weight: 8.6 oz
Operating Voltage: Two 1.5V AA alkaline batteries
Temperature Range: 40°F (4°C) to 100°F (38°C)
Humidity Range: 10% to 95% relative humidity (RH)
Audio Alarm: 85dB at 10 feet
Test/Silence: Electronically simulates smoke condition, causing the unit
to alarm. Press and hold test/silence button
Alarm Reset: Automatic when smoke clears
Smoke Sensors: Photoelectric and Ionization
Indicator Lights/Sounds:
DC Power: Intermittent Green LED
Local Alarm: Red LED flashes rapidly
Alarm Latch: LED flashes red 2 sec on, 2 sec off after local alarm stops
Low Battery Latch: LED flashes green 2 sec on, 2 sec off
Listing: Listed to UL217 Standard