Filter
Top Products
Handle Assembly
1. Carefully unpack all components,
set aside packaging.
2. Lift vacuum body to upright position.
3. Remove the screw (1) that comes
attached to the
body.
4. From the rear of
the vacuum, align
the handle with
groove and slide
onto vacuum. If
necessary, use
thumb and finger
pressure to slide
handle into position.
5. Once handle is in place, secure the
handle with the screws (2). (Fig. 1)
Caution: Do not over tighten. Over
tightening could strip the screw holes.
Do not operate the vacuum without
the handle screws in place.
Fig. 1
Cord Assembly
1. Make sure that the quick release
cord holder is in the upright
position.
2. Remove the wire
tie from the power
cord.
3. Wrap the cord into
place by wrapping
it in a clockwise
direction around
the quick release
cord holder and
the lower cord
holders. (Fig. 2)
4. Turn the quick
release cord holder
to the left or to the right to unwrap
the power cord. (Fig. 2)
Warning: Always make sure that the
vacuum is turned off
before unplugging.
Fig. 2
OPERATING INSTRUCTIONS
Assembling Your Vacuum Cleaner
Note: Do not plug the power cord
into an electrical outlet until
the vacuum is fully
assembled.
4
Using the Attachments
1. Place vacuum in its upright position.
Make sure that the vacuum cleaner
is NOT plugged into the electrical
outlet when adding or removing
accessories.
2. Turn the carpet height selector
to the highest position and set the
Carpet to Floor selector to the
“Floor” position.
3. Remove the hose connector from
the rear of the unit and push in the
desired attachment firmly onto the
end of the hose.
4. If additional length is required,
attach the extension tubes to the end
of the hose and then attach the
crevice tool, round brush or
upholstery brush to the end of the
extension tube.
Warning: Avoid tipping the vacuum or
setting it on furniture, fringed area rugs or
carpeted stairs while you are using the
hose with the attachments. When using
the unit to vacuum floors or with
attachments, set the Carpet to Floor
Selector to the “Floor” position. This will
stop the beater brush from rotating. When
vacuuming carpets, avoid leaving the
vacuum in one place for an extended
period of time, particularly on thick carpet.
How to Start
The upright vacuum can be used on
multiple types of carpeting, bare floors or
upholstery with attachments. When using
the attachment tools such as the crevice
tool, round brush or the upholstery brush,
place the handle of the vacuum in the
upright position.
1. Turn the quick release cord holder
to either side 180° to release the
power cord.
2. Plug the power cord into the electrical
outlet.
3. Push the On/Off
button to the "On"
position to turn
the vacuum on.
4. To release the
handle, step
on the power
head and pull the handle back.
5. When using the attachments, the
vacuum must be in the upright
position. (Fig. 3)
Caution: Do NOT pull the vacuum
cleaner around the room by the hose as it
could tip over and cause damage. When
using the attachments, do NOT over
extend the hose length when reaching.
Trying to reach beyond the hose reach
could cause the vacuum to tip over.
Fig. 3
Changing the Headlight Bulb
OPERATING INSTRUCTIONS
6. Remove the belt cover (Fig. 22, #1)
7. Lift the right side of the brush bar
first and then lift the left hand side.
(Fig. 22 #2, #3)
8. Remove the brush bar from the
power head. (Fig. 22, #4)
9. Carefully remove any belt residue
that may exist in the belt area before
replacing with a new belt.
10.Remove the worn or broken belt
from the motor drive shaft.
11 Loop the new belt first over the motor
drive shaft and then over the agitator
pulley.
1. Turn unit “Off” and unplug from wall
outlet.
2. With a flat head screw driver, snap off
the lens cover by pressing down on the
two notches on the lens cover. (Fig. 23)
3. Lift off the head light lens.
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
Fig. 22
Notches
Fig. 23
4. Remove the light bulb by pulling it
out carefully.
5. Replace the new bulb by pushing
it in.
6. Replace the head light lens by pushing
it in so that it snaps back in place.
12. Insert the right side of the brush
bar in first by placing the end cap
down into the slot and then do the
same with the left side. Press
firmly to make sure that each end
is completely inserted.
13. Check to make sure that the belt is
centered on the agitator pulley and
that the brush bar turns.
14. Replace the belt cover.
15. Replace the power head cover and
turn the unit over carefully.
16. Replace the lower plate, screwing
in the four (4) outer screws first.
17. When screwing in the center screw,
hold the carpet height adjustment
knob from the outside and screw in
the last screw.
18. Replace the lower plate.
19. Once the lower plate is attached,
replace the base plate with the four
(4) screws.
9