Filter
Top Products
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
On/Off Switch
The On/Off switch has three different
positions. (Fig.6)
• Push on the "I" side to turn the
vacuum ON. Set the vacuum here
when using the removable hose
handle with the accessories or when
vacuuming bare floors.
• Push on the “II" side to turn the
motorized floor brush on.
• Push on the “O” side to turn the
vacuum to the OFF position.
Using The Unit With The
Accessories
• Remove the removable
hose handle from
the hose connector.
• Attach the extension
tube, crevice tool,
the dusting brush,
pet hair brush or air
driven turbo brush
to the end of the
hose. (Fig. 8)
= OFF
= ON
(Bare Floors/Tools)
Using The Unit With The Motorized
Floor Brush
• Unwind the power cord and plug into
the 120V outlet.
• Press the On/Off switch to the “II”
position so that both the vacuum
and the motorized floor brush is
turned “ON”
NOTE: When vacuuming deep pile
carpets or hard wood floors, lower the
angle of the handle for easier
maneuverability. (Fig. 7)
= ON
(Carpet)
Fig. 6
Fig. 8
Fig. 7
Manual Variable Suction Control
Your vacuum cleaner includes a
variable suction control valve on the
hose handle. The suction power can be
adjusted by moving the slide to the
desired position. For example. Less
suction is required on upholstery and
draperies compared to thick shag
carpets, which require maximum
suction.
Dusting Brush
The dusting brush is used
for the furniture, venetian
blinds, books, lamp shades
and shelves.
Extension Tube
For hard to reach places. Use with
crevice tool or with dusting brush.
Wash
once a
month or
when
suction
appears
reduced
Fig. A
PLEASE NOTE: The white pleated
filter material in the HEPA Filter will
discolor over time -This is NORMAL
and will NOT affect the performance
of the filter. If the HEPA filter
is properly
"TapCleaned”
after each use
and suction
does not return
to 100%, then
we suggest that
the HEPA filter
be “TapCleaned”
vigorously until
no more dust
can be removed,
then rinsed under the faucet and
allowed to air dry for 24 hours before
refitting into the vacuum. (Fig. A)
This should be done once a month
or when suction appears to be
reduced.
Note: Even though the HEPA filter is
washable, it should be replaced every
3 to 6 months, depending on usage.
Warning: Allow 24
hours for drying before
replacing in unit.
Warning: Always empty the dust
cup container and clean the HEPA
filter, filter ring and debris screen
before each use and during
prolonged usage.
Please Note:
The HEPA Filter is
washable. It should, however, be
replaced every three (3) to six (6) months
to ensure peak performance of your
vacuum.
The filter ring and exhaust filter are also
rinseable but they should be air dried for
24 hours before replacing into the
vacuum. They should however be
replaced every three (3) months to
ensure peak performance of your
vacuum.
Important:
Make sure that ALL filters are
completely dry before re-installing back in
Never over fill the dust cup container -
remove dirt and clean the HEPA filter,
filter ring and debris screen when dirt
in dust cup is at or below the "MAX"
level or during prolonged usage
because you could risk damaging the
motor.
If you wash the Hepa filter, make
sure that it has completely air dried
for 24 hours before inserting back
into the vacuum.
2. To separate the filter assembly, hold
the bottom of the debris screen and
pull the dust cup cover out. Then
remove the HEPA filter with the filter
ring from the debris screen (Fig. 13)
3. Once you have removed the
HEPA filter from the debris
screen, remove the filter ring from
around the HEPA filter.
4. Vigorously “TapClean” the HEPA
filter on a hard surface until no
more dust is observed falling out.
(Fig. 14)
The HEPA
filter may also
be washed by
running it under
the tap allowing
the water to run on
the dirty side.
(Fig. 15) We
recommend
washing it once a
month or when
suction appears
reduced. Always
allow 24 hours for
air drying before
replacing into the vacuum.
Dust Cup
Cover
HEPA
Filter
Debris Screen
Fig. 13
Filter Assembly
Filter
Ring
Fig. 14
Warning: Never over fill the dust
cup - remove dirt and clean the
HEPA dust cup filter, filter ring and
debris screen each time the dust cup is
emptied during prolonged usage or risk
motor damage.
Fig. 15
Crevice Tool
For radiators, crevices, corners,
baseboards and between cushions.
Pet Hair Removal Brush
The pet hair removal brush
is for use on upholstery,
drapes and other fabric
surfaces to remove lint, pet
hair, etc. THE PET HAIR REMOVAL
BRUSH IS NOT INTENDED TO BE
USED AS A PET GROOMING
DEVICE.
8
the vacuum.
5