Filter
Top Products
OPERATING INSTRUCTIONS cont. OPERATING INSTRUCTIONS cont.
WINDING & UNWINDING THE
POWER CORD
This vacuum cleaner is
equipped with a convenient
cord storage feature. The
power cord winds around
the two cord holders at
the back of the unit. The
bottom one has a quick
cord release feature.
Turn the cord hook to
the left or the right to
remove the power cord.
See illustration at right.
ON/OFF SWITCH
• The On/Off switch has two different
positions.
• Push on the "I" side to turn the
vacuum ON.
• Push on the "O" side to turn the
vacuum OFF.
USING THE UNIT AS A HAND
VACUUM
• Press the telescopic tube release
button to remove the telescopic tube.
(See page 4)
• Press the floor brush release button to
remove the floor brush. (See page 4)
• Attach the shoulder strap to the
shoulder strap attachment point. (See
illustration below.)
• Attach the crevice tool or the dusting
brush to the end of the hose.
Crevice Tool
For radiators, crevices, corners,
baseboards and
between cushions.
Dusting Brush
The dusting brush is
used for the furniture,
venetian blinds,
books, lamp shades
and shelves.
USING THE UNIT AS AN UPRIGHT
• Unwind the power cord
and plug into the
120V outlet.
• Push down on the
locking button to adjust
the height of the
telescopic handle.
NOTE: When vacuuming
deep pile carpets or
hard to vacuum
carpets, lower the angle
of the telescopic
handle (see
illustration at
right) for
easier
maneuverability.
L
o
w
e
r
WARNING
After extended use, the body of the
vacuum cleaner may become hot.
When using the unit with the shoulder
strap, the unit will touch the body of
the user. Therefore, make sure that
the unit body is cool before you use
with the shoulder strap. If during use,
the vacuum gets too warm, allow it to
cool before continuing to use.
5
= OFF
= ON
Turbine
Tilt
Upwards
Locking Latch
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1.Remove the turbo brush from the hose
or extension tube.
2.Slide locking latch forward then tilt the
top housing of the brush upwards. The
top housing is hinged and will tilt up
approximately 45° only.
3.There may be some dust, lint, hair, etc
on the turbine wheel. Remove as much
of this as possible.
4.You may also use the unit’s hose with
crevice tool attached and use the
vacuum to remove any additional
debris from the turbine.
5.Ensure that the turbine wheel moves
freely by rotating it with your finger. If
the turbine does not rotate, call
Customer Service for help.
6.Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.
To use the air driven turbo brush to
clean upholstery:
1. Remove the flexible hose from the
hose connector. (See below)
2. Push the air driven turbo brush onto
the end of the flexible hose as far as
it will go.
Cleaning Air Driven Turbo Brush
6
Attaching the Air Driven Turbo
Brush to the Flexible Hose
Using The Unit With Air Driven
Turbo Brush
Air Driven Turbo Brush
Important: In order to ensure that
maximum air suction is maintained,
empty the dust cup frequently and
ensure that the rotating brush is kept free
of hair and string which may accumulate
and decrease brush performance.
The efficiency of your air driven turbo
brush depends on the bristle brush
rotating at high speed. Strong air suction
is needed to accomplish this. In order to
ensure that maximum air suction is
maintained, please read the following
instructions:
1.Empty the dust cup frequently.
2. Always shake out the dust cup filter
when emptying the dust cup container.
3.Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.
4.Keep Air Driven Turbo Brush turbine
free of dirt and foreign matter. (See
illustration for cleaning instructions.)
When the Intelli-Sense
TM
Filter
Monitor lights up, it means that the
dust cup is full or the HEPA filter or
Debris Screen needs cleaning.
You must empty the dust from the
dust cup and clean the HEPA filter
and Debris Screen right away.
Intelli-Sense
TM
Filter Monitor