Everpure XC2 Water System User Manual


  Open as PDF
of 4
 
• ConnecttheoutletoftheSR-XFeedertotheicemachinemake-upwater(notcondenserwater)
lineandcoffeebrewingequipment.Proceedtostep4.
3b.ForHighFlowCSRQuadPlusSystem,connectoutlettoequipmentservedpertheinstructionsbe-
low.AlwaysuseaNSFapprovedpipedopeorTeontapeatallconnections.Useabackupwrench
on all fittings while connecting to avoid stress on the system components.
• LocateandmounttheseparateSR-XFeederbetweentheHighFlowCSRsystemandtheice
machine.Make-upwater(notcondenserwater)lineandcoffeebrewingequipment.
• Ateettingislocatedinthesystemheaderbeforethesurgetankisolationandushingvalve.
Usingminimum1/2"I.D.line,connecttheoutletofthisteetothefountainbeverageandremote
SR-XFeederline.Important: Install a tee in this service water line to separate the fountain
water feed from the ice machine/coffee brewer water feed.
In Massachusetts, a backflow preventer is required for this installation.
• Connectonebranchoftheservicewaterteetothefountainbeverageequipment.Connectthe
otherbranchoftheteetotheinletoftheSR-XFeeder.ConnecttheoutletoftheSR-XFeederto
theicemachinemake-upwater(notcondenserwater)lineandcoffeebrewingequipment.
• Thesurgetankisolationandushingvalveislocatedattheendofthesystemheader.Using
ttingsandhoseprovided,connectonebranchofthevalvetothesurge/storagetank.Connect
ahosefromtheother(ushing)branchandruntodrain.Note: Some municipal plumbing codes
and good sanitary practices require an air gap at the drain termination point.
4. Thesurge/storagetankispre-pressurizedto20psi.Checkpressureandadjustasnecessary.
5. Installamanualshut-offvalveleadingtothesystemforservicingandconnectminimum1/2"I.D.
(3/4"forquad)waterlinetothesysteminlet.
6. TheoptionalEverguard
™
LowPressureAlarm(LPA)consistsofapressureswitch,audible/visual
alarmboxandapoweradapter.Itisdesignedtodetectaxedlowpressure(approx.20psi)
conditionasanindicationoflossofsystemoutletpressureeitherduetoanintentionalshut-down
orexcessfoulingofthewaterlters,thusindicatingtheneedforltercartridgechange-out.Ifthe
systemisequippedwiththeLPA,followthesesteps:
• Determinelocationofaconvenient110VACoutlettoplugintheLPApoweradapter.
• Removetheprotectiverubbercapfromthepressureswitchinstalledinthesystemheader
assembly.InsertthewiresfromtheLPAunitthroughthecapandconnectthemtotheterminals
onthepressureswitch.Eitherwirecanbeconnectedtoeitherterminal.Replacethecap.
• PlugtheLPApoweradapterintoanoutlet.Theaudiblealarmshouldactivate.Pushthereset
switch to silence.
• UnplugtheLPAunit.
7. Shutoffthesysteminletvalvelocatedontheinletoftheprelterhead.
8. Checktobesuretheo-ringontheprelterhousingissufcientlylubricated.Useagoodgradeof
siliconelubricant,ifneeded.PositiontheEC210preltercartridgeonguideseatinthebottomof
thebowl.Thenthreadthebowlintotheheadbyhand.Useasumpwrenchtosnugthebowlonto
the head.
9. InstallonlygenuineEverpure™carbonltercartridge(s)intothelterhead(s)followingdirections
onthecartridgelabelorasshownintheCartridgeChangeillustrations.InstalltheSS-10Scale
InhibitorcartridgeintotheSR-Xhousing.
10.Turnoninletwatertotheltersystemandcheckforleaks.
11.Opentheushingvalveandushthecartridge(s)byrunningwaterthroughatfullforceforve
minutes.Thiswillsetthelteringmediaandpurgeanyairandnes,insuringmaximumlterlife.
See illustrations.
12.Afterushing,closetheushingvalve,turnonpowertoequipmentandplugtheLPA(ifso
equipped)intotheelectricaloutlet.Thesystemisreadyforoperation.
Figure5–HighFlowCSRTwin
25.80"
ICE MACHINE/
COFFEE
OUTLET
3/4" FNPT
INLET
3/4" FNPT
FOUNTAIN
OUTLET
3/4" FNPT
25.59"
Figure6–HighFlowCSRTriple
25.59"
30"
INLET
3/4" FNPT
ICE MACHINE/
COFFEE
OUTLET
3/4" FNPT
FOUNTAIN
OUTLET
3/4" FNPT
Figure8–HighFlowCSRQuadPlus
29.69"
OUTLET
3/4" FNPT
INLET
3/4" FNPT
ICE MACHINE/
COFFEE
OUTLET
3/4" FNPT
INLET
3/4" FNPT
INSERT TEE FITTING.
ONE OUTLET TO FOUNTAIN,
ONE OUTLET TO SRX.
31.38"
Figure7–HighFlowCSRQuad
34"
INLET
3/4" FNPT
ICE MACHINE/
COFFEE
OUTLET
3/4" FNPT
FOUNTAIN
OUTLET
3/4" FNPT
25.69"
Checkforcompliancewithstateandlocallawsand
regulations.TheCommonwealthofMassachusetts
PlumbingCode248CMRshallbeadheredto.Consultyour
locallicensedplumberforinstallationofthissystem.Do
notusewithwaterthatismicrobiologicallyunsafeorof
unknownqualitywithoutadequatedisinfectionbeforeor
after the system. Systems certified for cyst reduction may
beusedondisinfectedwatersthatmaycontainlterable
cysts.
FLUSHING
For maximum life, all carbon filter cartridges must be flushed for five minutes at full flow before use. ALL
NEW CARTRIDGES MUST BE FLUSHED AFTER EACH CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!
Ifthecartridgesarenew,havebeenproperlyushedandbothneedleandfollowerregisterinadequatepressure,or
theLPAissounding,youmaybeexperiencinginadequatewaterpressureorsomerestrictionmayexistintheinlet
waterline.Ineithercase,theincomingwaterpressuremustbeimprovedtoreceiveoptimumlterlife.
COMPLETECARTRIDGECHANGEINSTRUCTIONSCANBEFOUNDONTHEFILTERCARTRIDGELABEL.
Not for residential use. For food service applications only.
 previous next