Everpure SPA-400 Water System User Manual


  Open as PDF
of 2
 
product specifications
Everpure, Micro-Pure andthe silver canister color are registered trademarks of Everpure, LLC © 2008
®
®
SPA-400
Commercial grade drinking water system
for the home spa and bath
This drinking water system must be
maintained according to the
manufacturer's instructions, including
replacement of filter cartridges. The
substances reduced or removed by this
system are not necessarily in your water.
Read the performance data sheet.
flow rate
Controlled at 2.2 gal./min. (8.3 L/min.)
temperature
35-100 °F (2-38 °C) cold water use only
pressure
10-125 psi. (0.7-8.6 bar), non-shock
capacity
3,000 gal. (11,356 L)
everpure warranty
Everpure Drinking Water Systems are
warranted to be free of defects for a full
twelve (12) months after purchase. A
detailed warranty statement is provided
with each system.
SPA-400 System – Part No. EV9270-90
SPA-400 Cartridge – Part No. EV9270-91
Features:
> Finely polishes treated water to premium quality for drinking.
> Reduces chlorine taste and odor.
> Reduces dirt, rust, and other particulates such as oxidized iron, manganese, and sulfides.
> Reduces parasitic protozoan cysts such as Giardia, Entamoeba, and Cryptosporidium.
> Reduces common earthy, moldy, fishy tastes, and odors.
> Reduces lead to below the Federal Action Level.
General Installation/Operation/Maintenance Requirements:
> It is recommended that before purchasing a water treatment unit, you have your water tested to
determine your actual treatment needs.
> Space required: 5 x 5 x 20 in. (13 x 13 x 51 cm) including 2-1/2 inches of clear space under unit for
cartridge change.
> Install vertically with cartridge hanging down.
> Use minimum length of tubing possible.
> Flush new cartridge at full flow for three minutes to purge air.
> Replace cartridges when capacity is reached, or when flow becomes too slow, but at least annually.
> Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system. Systems certified for cyst reduction may be used on
disinfected water that may contain filterable cysts.
> System comes complete with filter cartridge, head, fittings, and connector.
Std. No. 42—Aesthetic effects
Chemical Reduction
Chlorine
Taste & Odor
Mechanical Filtration
Nominal Particulate Class I
Std. No. 53—Health effects
Chemical Reduction
Lead
Mechanical Filtration
Cyst
Turbidity
System Tested and Classified by Underwriters
Laboratories against NSF/ANSI Standards 42 and 53 as
verified and substantiated by test data for the reduction of:
ANSI/NSF
STANDARDS
42 and 53
HEALTH CLAIM PERFORMANCE CLASSIFIED BY UL
This system has been tested according to NSF/ANSI 42 and 53 for
the reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a
concentration less than or equal to the permissible limit for water leaving
the system, as specified in NSF/ANSI 42 and 53.
Substance
Influent Challenge
Concentration
Max. Permissible
Product Water
Concentration
Reduction
Requirements
Minimum
Reduction
Average
Reduction
Standard 42—Aesthetic Effects
Chlorine 2.0 mg/L ± 10% ≥ 50% 98%
Particulate,
Class I
particles 0.5
to <1 µm
at least 10,000
particles/mL
≥ 85% 99.8%
Standard 53—Health Effects
Cyst Minimum 50,000/L 99.95% 99.99% 99.99%
Lead 8.5 0.15 mg/L ± 10% 0.010 mg/L 94.1% 97.2%
Lead 6.5 0.15 mg/L ± 10% 0.010 mg/L 98.9% 98.9%
Turbidity 11±1 NTU 0.5 NTU 98% 99%
†NTU = Nephelometric Turbidity Units
 previous